cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
370
Views
5
Helpful
4
Replies

PPPoE over VLAN configuration

Gregorygrzegorz
Beginner
Beginner

Hey there,

 

I have Cisco ISR 900 device. I'm trying to pass traffic from my vlan 10 via dialer 1(ppoe client).

When i tested ping from dialer 1 it works but i can not combine dialer and vlan.

Can anyone see what i'm doing wrong?

 

Config in spoiler:

Spoiler


Building configuration...

Current configuration : 2637 bytes
!
! Last configuration change at
!
version 15.8
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
!
!
!
!
!
!
ip dhcp excluded-address 10.0.0.0 10.0.0.50
!
ip dhcp pool LAN
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.254
dns-server 172.64.36.1 172.64.36.2
lease 0 1
!
!
!
ip name-server 172.64.36.1
ip name-server 172.64.36.2
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
vpdn enable
!
vpdn-group 1
!
!
!
license udi pid C921-4P sn xxxxxxxx
!
!
username xxxxxx privilege 15 secret 5 $xxxxxxxxxxxx
!
redundancy
!
!
!
!
!
!
interface GigabitEthernet0
description Lan connection
switchport access vlan 10
no ip address
!
interface GigabitEthernet4
description PrimaryWANDesc_internet connection
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface GigabitEthernet5
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
no ip address
!
interface Vlan10
description Vlan 10
ip address 10.0.0.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
no ip address
!
interface Dialer1
mtu 1480
ip address negotiated
ip mtu 1480
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1412
dialer pool 1
dialer-group 1
ppp mtu adaptive
ppp authentication chap callin
ppp chap hostname xxxx
ppp chap password 0 xxxx
!
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
!
!
ip route 0.0.0.0 0.0.0.0 Dialer1
!
dialer-list 1 protocol ip permit
!
!
access-list 1 permit any
!
control-plane
!
!
line con 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end

 

Thanks in advance for help

 

 

1 Accepted Solution

Accepted Solutions

Georg Pauwen
VIP Master VIP Master
VIP Master

Hello,

you can also try the below (changes marked in bold

Building configuration...

Current configuration : 2637 bytes
!
! Last configuration change at
!
version 15.8
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
ip dhcp excluded-address 10.0.0.0 10.0.0.50
!
ip dhcp pool LAN
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.254
dns-server 172.64.36.1 172.64.36.2
lease 0 1
!
ip name-server 172.64.36.1
ip name-server 172.64.36.2
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
vpdn enable
!
vpdn-group 1
!
license udi pid C921-4P sn xxxxxxxx
!
username xxxxxx privilege 15 secret 5 $xxxxxxxxxxxx
!
redundancy
!
interface GigabitEthernet0
description Lan connection
switchport access vlan 10
no ip address
!
interface GigabitEthernet4
description PrimaryWANDesc_internet connection
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface GigabitEthernet5
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
no ip address
!
interface Vlan10
description Vlan 10
ip address 10.0.0.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
no ip address
!
interface Dialer1
mtu 1480
ip address negotiated
ip mtu 1480
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1412
dialer pool 1
dialer-group 1
ppp mtu adaptive
ppp authentication chap callin
ppp chap hostname xxxx
ppp chap password 0 xxxx
!
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
!
--> ip nat inside source list 1 interface Dialer1 overload
!
ip route 0.0.0.0 0.0.0.0 Dialer1
!
dialer-list 1 protocol ip permit
!
--> access-list 1 permit 10.0.0.0 0.0.0.255
!
control-plane
!
line con 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end

View solution in original post

4 Replies 4

MHM Cisco World
Advisor
Advisor

sorry I dont see attach config 
as @balaji.bandi  mention you need NAT overload, 
if not success 
share 
show ip route 

balaji.bandi
VIP Community Legend VIP Community Legend
VIP Community Legend

add below line and test it.

access-list 100 permit 10.0.0.0 0.0.0.255 any
ip nat inside source list 100 interface Dialer1 overload

 

Note : dns-server 172.64.36.1 172.64.36.2  ( if this is valid DNS ok, if not change to 8.8.8.8 google DNS if browsing not working)

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Georg Pauwen
VIP Master VIP Master
VIP Master

Hello,

you can also try the below (changes marked in bold

Building configuration...

Current configuration : 2637 bytes
!
! Last configuration change at
!
version 15.8
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
ip dhcp excluded-address 10.0.0.0 10.0.0.50
!
ip dhcp pool LAN
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.254
dns-server 172.64.36.1 172.64.36.2
lease 0 1
!
ip name-server 172.64.36.1
ip name-server 172.64.36.2
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
vpdn enable
!
vpdn-group 1
!
license udi pid C921-4P sn xxxxxxxx
!
username xxxxxx privilege 15 secret 5 $xxxxxxxxxxxx
!
redundancy
!
interface GigabitEthernet0
description Lan connection
switchport access vlan 10
no ip address
!
interface GigabitEthernet4
description PrimaryWANDesc_internet connection
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface GigabitEthernet5
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
no ip address
!
interface Vlan10
description Vlan 10
ip address 10.0.0.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
no ip address
!
interface Dialer1
mtu 1480
ip address negotiated
ip mtu 1480
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1412
dialer pool 1
dialer-group 1
ppp mtu adaptive
ppp authentication chap callin
ppp chap hostname xxxx
ppp chap password 0 xxxx
!
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
!
--> ip nat inside source list 1 interface Dialer1 overload
!
ip route 0.0.0.0 0.0.0.0 Dialer1
!
dialer-list 1 protocol ip permit
!
--> access-list 1 permit 10.0.0.0 0.0.0.255
!
control-plane
!
line con 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end

It works thank you very much 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: