cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
694
Views
0
Helpful
3
Replies

ASA 5505 DMZ Vlan

swashbuckler
Level 1
Level 1

I have a base license and created a DMZ vlan 3.

Problem I have is I cannot communicate between my networks and I cannot get to the outside on vlan 3 (DMZ)

Ethernet0/0 outside

Ethernet0/1 inside Computer 1  10.200.1.248

Ethernet0/2 DMZ Computer 2 172.16.17.15

Ethernet0/3 inside Computer 3 10.200.1.249

Computer 3 can ping computer 1

Computer 1 cannot ping computer 3

Computer 2 cannot ping computers 1 and 3

Computers 1 and 3 cannot ping computer 2

interface Vlan1
nameif inside
security-level 100
ip address 10.200.1.241 255.255.255.240
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
interface Vlan3
no forward interface Vlan1
nameif DMZ
security-level 50
ip address 172.16.17.1 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
switchport access vlan 3
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
object-group network DMZ_outside

access-list outside_access extended permit icmp any any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu DMZ 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any echo inside
icmp permit any echo-reply inside
no asdm history enable
arp timeout 14400
global (outside) 1 interface
global (DMZ) 2 interface
nat (inside) 0 access-list nonat
nat (inside) 1 0.0.0.0 0.0.0.0
nat (outside) 2 0.0.0.0 0.0.0.0
static (DMZ,outside) 172.16.17.0 255.255.255.0 netmask 255.255.255.255
access-group outside_access in interface DMZ
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 10.200.1.240 255.255.255.240 inside

no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set mytrans esp-des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000

crypto map mymap 10 set transform-set mytrans
crypto map mymap 10 set security-association lifetime seconds 3600
crypto map mymap interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
crypto isakmp nat-traversal 21
telnet timeout 5

ssh timeout 5
console timeout 0
management-access inside
dhcpd dns 75.75.75.75
dhcpd auto_config outside
!
dhcpd address 10.200.1.242-10.200.1.250 inside
dhcpd enable inside
!

threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username rignetadmin password AJ8NEgTh4zmR7lck encrypted privilege 15

pre-shared-key *
!
!
prompt hostname context
Cryptochecksum:9b9d69fbcc9f7a38b081fac96038ae5e
: end

Thanks in advance for any help,

Bobby

1 Accepted Solution

Accepted Solutions

You can can create 3 VLANs when running a base license but the 3rd VLAN will not be able to communicate with anything else. for this to work you need to upgrade to a security plus license.

If you issue the show version command you will see that the VLAN section of activated features says restricted...or something similar

--
Please remember to select a correct answer and rate helpful posts

View solution in original post

3 Replies 3

You can can create 3 VLANs when running a base license but the 3rd VLAN will not be able to communicate with anything else. for this to work you need to upgrade to a security plus license.

If you issue the show version command you will see that the VLAN section of activated features says restricted...or something similar

--
Please remember to select a correct answer and rate helpful posts

That I know, i thought traffic is restricted to vlan1 from dmz but not from vlan1 to the dmz

Bobby

Here is an update:

disregard the communication of the computers.

I do have the DMZ access to the outside now.

But I do not have access from inside vlan1 to the DMZ vlan3.

Bobby

Unfortunately that is not the case.  with the base license there can only be 2 active VLANs at any one time.

--
Please remember to select a correct answer and rate helpful posts
Review Cisco Networking for a $25 gift card