ASA 5505 help! wont boot

[leetobin1982]

Any help will be great this is all I get from the console. Any suggestions will be great. Everything was woking perfectly!

CISCO SYSTEMS

Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45

Low Memory: 632 KB

High Memory: 507 MB

PCI Device Table.

Bus Dev Func VendID DevID Class              Irq

00  01  00   1022   2080  Host Bridge

00  01  02   1022   2082  Chipset En/Decrypt 11

00  0C  00   1148   4320  Ethernet           11

00  0D  00   177D   0003  Network En/Decrypt 10

00  0F  00   1022   2090  ISA Bridge

00  0F  02   1022   2092  IDE Controller

00  0F  03   1022   2093  Audio              10

00  0F  04   1022   2094  Serial Bus         9

00  0F  05   1022   2095  Serial Bus         9

Evaluating BIOS Options ...

Launch BIOS Extension to setup ROMMON

Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008

[johnlloyd_13]

hi lee,

looks like the IOS got deleted or corrupted.

you'll need to upload the IOS via ROMMON/TFTPDNLD by pressing the escape key.

rommon #1> address 192.168.1.1

rommon #2> server 192.168.1.2    <<< YOUR PC WITH TFTP

rommon #3> file

rommon #4> tftpdnld

[leetobin1982]

Thanks for taking time to look at this, I dont think i can reach rommon. I get "invalid Key" pressing ESC.

It wint boot any further than shown on the console output. I dont know if it helps but im using putty.

High Memory: 507 MB

PCI Device Table.

Bus Dev Func VendID DevID Class              Irq

00  01  00   1022   2080  Host Bridge

00  01  02   1022   2082  Chipset En/Decrypt 11

00  0C  00   1148   4320  Ethernet           11

00  0D  00   177D   0003  Network En/Decrypt 10

00  0F  00   1022   2090  ISA Bridge

00  0F  02   1022   2092  IDE Controller

00  0F  03   1022   2093  Audio              10

00  0F  04   1022   2094  Serial Bus         9

00  0F  05   1022   2095  Serial Bus         9

Evaluating BIOS Options ...

Invalid Key: 001B

Invalid Key: 001B

Invalid Key: 001B

Launch BIOS Extension to setup ROMMON

Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008

[narawat]

Hi Lee,

     what happens to the status light ?

I think you would need to replace the device, still would like to clarify the status light situation when the firewall boots.

Cheers,

Naveen

[leetobin1982]

I've got a solid status and power light.

[johnlloyd_13]

Could you try using 'Break' key instead?

Sent from Cisco Technical Support iPhone App

[leetobin1982]

Hi, thanks for the help tried that and nothing. Same key error.

[leetobin1982]

Ive left it a few hours and ive got this.

Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008

CISCO SYSTEMS

Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45

Low Memory: 632 KB

High Memory: 507 MB

PCI Device Table.

Bus Dev Func VendID DevID Class              Irq

00  01  00   1022   2080  Host Bridge

00  01  02   1022   2082  Chipset En/Decrypt 11

00  0C  00   1148   4320  Ethernet           11

00  0D  00   177D   0003  Network En/Decrypt 10

00  0F  00   1022   2090  ISA Bridge

00  0F  02   1022   2092  IDE Controller

00  0F  03   1022   2093  Audio              10

00  0F  04   1022   2094  Serial Bus         9

00  0F  05   1022   2095  Serial Bus         9

Evaluating BIOS Options ...

Launch BIOS Extension to setup ROMMON

Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008

i2c_read_word_w_wait() error, slot = 0x0, device = 0x64, address = 134 byte count = 2. Reason: I2C_HOST_BUSY_ERROR

Platform ASA5505

Use BREAK or ESC to interrupt boot.

Use SPACE to begin boot immediately.