cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2173
Views
0
Helpful
16
Replies

ASA 5505

POWELLMI01
Level 1
Level 1

   I have an inherited ASA 5505 V09.  It will not allow connection to the ASDM web page using the default IPaddress followed by /ADMIN.  It does provide DHCP address assignment to connected devices.  It does respond to the console connection using a Telnet type access.  I have restored the factory default (thinking the firmware needed refreshing) and did a WRITE MEMORY command (successful).  Does anyone have any suggestions as to how to correct this dilema?  I'm running asa821-k8.bin with 512 MB memory.               

1 Accepted Solution

Accepted Solutions

Hello Robert,

This should be working by now,

What are you getting on the Java logs???

What java version are you running?

Not sure if we discussed this before, but from the computer can you ping the ASA inside IP address??

Regards

Julio Carvajal
Senior Network Security and Core Specialist
CCIE #42930, 2xCCNP, JNCIP-SEC

View solution in original post

16 Replies 16

Yasien Adams
Level 1
Level 1

Hi,

Im assuming you have a console connection via console cable?

But you have no Telnet or ASDM access?

Firstly, can you verify that HTTP server is enabled, and check if an access policy is being applied to it.

Then you can check VTY access and check if it too has an access policy applied to it.

Are you trying to browse to the ASA? or are you using ASDM installed on your local machine?

I have a console connection using the console cable supplied by Cisco.  I do have Telnet access.  It appears I have manual control of the appliance as I can issue commands and receive responses.

In the startup configuration the server is listed (default Cisco configuration) so I think the HTTP server is active.  Is there a command I can issue to verify HTTP service?

I am trying to use the default ASA 5505 ASDM access using 192.168.1.1/admin but I get connectivity errors on the IE 8.0 browser.

I am new to the ASA commands so if you know of some command I should try, feel free to mention it.  I can look it up to get the appropriate parameters and required access level.

Hello Robert,

Provide:

Show run http

Show run asdm

Show flash

Show run aaa

Julio Carvajal
Senior Network Security and Core Specialist
CCIE #42930, 2xCCNP, JNCIP-SEC

I had already reset the appliance to factory settings to be sure there were no surprises.  Following is a log of the information you requested with some additional displays.

ciscoasa# show run http
http server enable
http 192.168.1.0 255.255.255.0 inside

ciscoasa# show run asdm

no asdm history enable

ciscoasa# show flash
--#--  --length--  -----date/time------  path
  182  16275456    Feb 09 2011 10:07:22  asa821-k8.bin
  183  49152       Jan 01 1980 00:00:00  FSCK0000.REC
   13  2048        Feb 09 2011 10:09:22  coredumpinfo
   14  43          Apr 03 2013 19:07:14  coredumpinfo/coredump.cfg
  184  11348300    Feb 09 2011 10:10:14  asdm-621.bin
    3  2048        Feb 09 2011 10:13:52  log
   12  2048        Feb 09 2011 10:14:00  crypto_archive
  186  2048        Jan 01 1980 00:00:00  FSCK0001.REC
  187  12105313    Feb 09 2011 10:14:16  csd_3.5.841-k9.pkg
  188  2048        Feb 09 2011 10:14:18  sdesktop
  223  0           Feb 09 2011 10:14:18  sdesktop/data.xml
  189  2857568     Feb 09 2011 10:14:18  anyconnect-wince-ARMv4I-2.4.1012-k9.pkg
  190  3203909     Feb 09 2011 10:14:20  anyconnect-win-2.4.1012-k9.pkg
  191  4832344     Feb 09 2011 10:14:22  anyconnect-macosx-i386-2.4.1012-k9.pkg
  192  5209423     Feb 09 2011 10:14:24  anyconnect-linux-2.4.1012-k9.pkg
  193  2048        Jan 01 1980 00:00:00  FSCK0002.REC
  194  2048        Jan 01 1980 00:00:00  FSCK0003.REC
  195  92160       Jan 01 1980 00:00:00  FSCK0004.REC
  196  2048        Jan 01 1980 00:00:00  FSCK0005.REC
  197  2048        Jan 01 1980 00:00:00  FSCK0006.REC
  198  2048        Jan 01 1980 00:00:00  FSCK0007.REC
  199  675840      Jan 01 1980 00:00:00  FSCK0008.REC
  200  2048        Jan 01 1980 00:00:00  FSCK0009.REC
  201  677888      Jan 01 1980 00:00:00  FSCK0010.REC       
  202  30720       Jan 01 1980 00:00:00  FSCK0011.REC

  203  30720       Jan 01 1980 00:00:00  FSCK0012.REC        
  204  2048        Jan 01 1980 00:00:00  FSCK0013.REC        
  205  2048        Jan 01 1980 00:00:00  FSCK0014.REC          
  206  4096        Jan 01 1980 00:00:00  FSCK0015.REC             
  207  4096        Jan 01 1980 00:00:00  FSCK0016.REC             
  208  4096        Jan 01 1980 00:00:00  FSCK0017.REC        
  209  4096        Jan 01 1980 00:00:00  FSCK0018.REC             
  210  6144        Jan 01 1980 00:00:00  FSCK0019.REC
  211  6144        Jan 01 1980 00:00:00  FSCK0020.REC           
  212  6144        Jan 01 1980 00:00:00  FSCK0021.REC             
  213  22528       Jan 01 1980 00:00:00  FSCK0022.REC           
  214  38912       Jan 01 1980 00:00:00  FSCK0023.REC            
  215  34816       Jan 01 1980 00:00:00  FSCK0024.REC            
  216  43008       Jan 01 1980 00:00:00  FSCK0025.REC            
  217  2048        Jan 01 1980 00:00:00  FSCK0026.REC             
  218  26624       Jan 01 1980 00:00:00  FSCK0027.REC            
  219  2048        Jan 01 1980 00:00:00  FSCK0028.REC            
  220  26624       Jan 01 1980 00:00:00  FSCK0029.REC            
  221  2048        Jan 01 1980 00:00:00  FSCK0030.REC            

             
127135744 bytes total (69373952 bytes free)

ciscoasa# show aaa   run aaa

ciscoasa# show aaa-server
Server Group: LOCAL
Server Protocol: Local database
Server Address: None
Server port: None
Server status: ACTIVE, Last transaction at unknown
Number of pending requests0
Average round trip time0ms
Number of authentication requests0
Number of authorization requests0
Number of accounting requests0
Number of retransmissions0
Number of accepts0
Number of rejects0
Number of challenges0
Number of malformed responses0
Number of bad authenticators0
Number of timeouts0
Number of unrecognized responses0


ciscoasa# show startup-config
: Saved
: Written by enable_15 at 19:07:13.999 UTC Wed Apr 3 2013
!
ASA Version 8.2(1)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!           
interface Ethernet0/2          
!             
interface Ethernet0/3            
!            
interface Ethernet0/4             
!             
interface Ethernet0/5             
!             
interface Ethernet0/6            
!             
interface Ethernet0/7             
!            
ftp mode passive             
pager lines 24             
logging asdm informational            
mtu inside 1500             
mtu outside 1500             
icmp unreachable rate-limit 1 burst-size 1

             
no asdm history enable

             
arp timeout 14400             
global (outside) 1 interface             
nat (inside) 1 0.0.0.0 0.0.0.0

             
timeout xlate 3:00:00             
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02             
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00             
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00            
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable

http 192.168.1.0 255.255.255.0 inside
no snmp-server location

no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800

crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5  
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.254 inside
dhcpd enable inside
!
    

threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
  
webvpn
!
  
!
 
prompt hostname context
Cryptochecksum:df13f02418c45ffcfe085bf14bc0348d

ciscoasa# exit

Logoff

Hello Robert,

You are missing this command:

asdm image flash:asdm-621.bin

Regards,

Let me know the results

Julio Carvajal
Senior Network Security and Core Specialist
CCIE #42930, 2xCCNP, JNCIP-SEC

I entered priveleged configure mode and issued the command as you specified.  It did not appear to change anything.  It did seem to accept the command.  Did I enter it properly?  I am new to this so you may have to be very exact as to where you want the command placed.  Here are some of the results:

ciscoasa# show flash
--#--  --length--  -----date/time------  path
  182  16275456    Feb 09 2011 10:07:22  asa821-k8.bin
  183  49152       Jan 01 1980 00:00:00  FSCK0000.REC
   13  2048        Feb 09 2011 10:09:22  coredumpinfo
   14  43          Apr 05 2013 18:25:41  coredumpinfo/coredump.cfg
  184  11348300    Feb 09 2011 10:10:14  asdm-621.bin
    3  2048        Feb 09 2011 10:13:52  log
   12  2048        Feb 09 2011 10:14:00  crypto_archive
  186  2048        Jan 01 1980 00:00:00  FSCK0001.REC
  187  12105313    Feb 09 2011 10:14:16  csd_3.5.841-k9.pkg
  188  2048        Feb 09 2011 10:14:18  sdesktop
  223  0           Feb 09 2011 10:14:18  sdesktop/data.xml
  189  2857568     Feb 09 2011 10:14:18  anyconnect-wince-ARMv4I-2.4.1012-k9.pkg
  190  3203909     Feb 09 2011 10:14:20  anyconnect-win-2.4.1012-k9.pkg
  191  4832344     Feb 09 2011 10:14:22  anyconnect-macosx-i386-2.4.1012-k9.pkg
  192  5209423     Feb 09 2011 10:14:24  anyconnect-linux-2.4.1012-k9.pkg
  193  2048        Jan 01 1980 00:00:00  FSCK0002.REC
  194  2048        Jan 01 1980 00:00:00  FSCK0003.REC
  195  92160       Jan 01 1980 00:00:00  FSCK0004.REC
  196  2048        Jan 01 1980 00:00:00  FSCK0005.REC
  197  2048        Jan 01 1980 00:00:00  FSCK0006.REC
  198  2048        Jan 01 1980 00:00:00  FSCK0007.REC
  199  675840      Jan 01 1980 00:00:00  FSCK0008.REC
  200  2048        Jan 01 1980 00:00:00  FSCK0009.REC
  201  677888      Jan 01 1980 00:00:00  FSCK0010.REC       
  202  30720       Jan 01 1980 00:00:00  FSCK0011.REC
  203  30720       Jan 01 1980 00:00:00  FSCK0012.REC
  204  2048        Jan 01 1980 00:00:00  FSCK0013.REC
  205  2048        Jan 01 1980 00:00:00  FSCK0014.REC
  206  4096        Jan 01 1980 00:00:00  FSCK0015.REC
  207  4096        Jan 01 1980 00:00:00  FSCK0016.REC
  208  4096        Jan 01 1980 00:00:00  FSCK0017.REC
  209  4096        Jan 01 1980 00:00:00  FSCK0018.REC
  210  6144        Jan 01 1980 00:00:00  FSCK0019.REC
  211  6144        Jan 01 1980 00:00:00  FSCK0020.REC
  212  6144        Jan 01 1980 00:00:00  FSCK0021.REC
  213  22528       Jan 01 1980 00:00:00  FSCK0022.REC
  214  38912       Jan 01 1980 00:00:00  FSCK0023.REC
  215  34816       Jan 01 1980 00:00:00  FSCK0024.REC
  216  43008       Jan 01 1980 00:00:00  FSCK0025.REC
  217  2048        Jan 01 1980 00:00:00  FSCK0026.REC
  218  26624       Jan 01 1980 00:00:00  FSCK0027.REC
  219  2048        Jan 01 1980 00:00:00  FSCK0028.REC
  220  26624       Jan 01 1980 00:00:00  FSCK0029.REC
  221  2048        Jan 01 1980 00:00:00  FSCK0030.REC

127135744 bytes total (69373952 bytes free)

ciscoasa# show running-config
: Saved
:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2             
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.254 inside
dhcpd enable inside
!

threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept             
webvpn
!
!
prompt hostname context
Cryptochecksum:8ea61ab256c327cfb8554acbd16f03e4
: end

ciscoasa# show configuration
: Saved
: Written by enable_15 at 18:20:14.379 UTC Fri Apr 5 2013
!
ASA Version 8.2(1)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!             
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.254 inside
dhcpd enable inside
!

threat-detection basic-threat
threat-detection statistics access-list             
no threat-detection statistics tcp-intercept
webvpn
!
!
prompt hostname context
Cryptochecksum:8ea61ab256c327cfb8554acbd16f03e4

ciscoasa#

Hello Robert,

It looks good to me now, you were missing that command ( U have it now)

are you entering

https://192.168.1.1 On a computer on the inside interface??

Can you enable the following

debug http 255

and then try to connect

Share the debugs

Julio Carvajal
Senior Network Security and Core Specialist
CCIE #42930, 2xCCNP, JNCIP-SEC

I connected to port 2 with the computer and entered http://192.168.1.1.  Then I entered http://192.168.1.1/admin.  In both cases the Internet Explorer cannot display the webpage was received.  I have attached the short debug information.

debug http 255
debug http enabled at level 255.

ciscoasa# HTTP: Periodic admin session check  (idle-timeout = 1200, session-timeout = 0)
HTTP: Periodic admin session check  (idle-timeout = 1200, session-timeout = 0)
admin     HTTP: Periodic admin session check  (idle-timeout = 1200, session-timeout = 0)
HTTP: Periodic admin session check  (idle-timeout = 1200, session-timeout = 0)
HTTP: Periodic admin session check  (idle-timeout = 1200, session-timeout = 0)
exit

Logoff

Your configuration allows http on the Inside (VLAN 1) interfaces but you only have a single switch port assigned to any VLAN - e0/0 assigned to Outside (VLAN 2).

Assign a port to the Inside VLAN 1 and try your ASDM login from a PC connected there.

Here is the relevant configuration guide section:

http://www.cisco.com/en/US/docs/security/asa/asa82/configuration/guide/intrface.html#wp1088804

Hello Marvin,

By default all ports belong to vlan 1, it is implicited that they are assigned to vlan 1 even if that does not appear on the config.

Robert,

from that computer can you ping 192.168.1.1?

Julio Carvajal
Senior Network Security and Core Specialist
CCIE #42930, 2xCCNP, JNCIP-SEC

Sorry I didn't reply sooner.  I inadvertently lost the configuration but I think I'm OK now.  I'm using asa821-k8.bin and asdm-621.bin on the appliance.  I added the command asdm image flash:asdm-621.bin to the restored factory configuration.  I am using port 2 for the host connection (VLAN1).  I ping 192.168.1.1 from the host connected to port 2 and receive the standard successful reply.

Is the http 192.168.1.0 255.255.255.0 inside statement correct in the factory configuration?

enable 15
Password:

ciscoasa# configure terminal

ciscoasa(config)# show flash
--#--  --length--  -----date/time------  path
   58  16275456    Feb 09 2011 10:07:22  asa821-k8.bin
   59  49152       Jan 01 1980 00:00:00  FSCK0000.REC
   13  2048        Feb 09 2011 10:09:22  coredumpinfo
   14  43          Apr 07 2013 07:53:11  coredumpinfo/coredump.cfg
   60  11348300    Feb 09 2011 10:10:14  asdm-621.bin
    3  2048        Feb 09 2011 10:13:52  log
   12  2048        Feb 09 2011 10:14:00  crypto_archive
   62  2048        Jan 01 1980 00:00:00  FSCK0001.REC
   63  12105313    Feb 09 2011 10:14:16  csd_3.5.841-k9.pkg
   64  2048        Feb 09 2011 10:14:18  sdesktop
  103  0           Feb 09 2011 10:14:18  sdesktop/data.xml
   65  2857568     Feb 09 2011 10:14:18  anyconnect-wince-ARMv4I-2.4.1012-k9.pkg
   66  3203909     Feb 09 2011 10:14:20  anyconnect-win-2.4.1012-k9.pkg
   67  4832344     Feb 09 2011 10:14:22  anyconnect-macosx-i386-2.4.1012-k9.pkg
   68  5209423     Feb 09 2011 10:14:24  anyconnect-linux-2.4.1012-k9.pkg
   69  2048        Jan 01 1980 00:00:00  FSCK0002.REC
   70  2048        Jan 01 1980 00:00:00  FSCK0003.REC
   71  92160       Jan 01 1980 00:00:00  FSCK0004.REC
   72  2048        Jan 01 1980 00:00:00  FSCK0005.REC
   73  2048        Jan 01 1980 00:00:00  FSCK0006.REC
   74  2048        Jan 01 1980 00:00:00  FSCK0007.REC
   75  675840      Jan 01 1980 00:00:00  FSCK0008.REC
   76  2048        Jan 01 1980 00:00:00  FSCK0009.REC
   77  677888      Jan 01 1980 00:00:00  FSCK0010.REC

   78  30720       Jan 01 1980 00:00:00  FSCK0011.REC
   79  30720       Jan 01 1980 00:00:00  FSCK0012.REC
   80  2048        Jan 01 1980 00:00:00  FSCK0013.REC
   81  2048        Jan 01 1980 00:00:00  FSCK0014.REC
   82  4096        Jan 01 1980 00:00:00  FSCK0015.REC
   83  4096        Jan 01 1980 00:00:00  FSCK0016.REC
   84  4096        Jan 01 1980 00:00:00  FSCK0017.REC
   85  4096        Jan 01 1980 00:00:00  FSCK0018.REC
   86  6144        Jan 01 1980 00:00:00  FSCK0019.REC
   87  6144        Jan 01 1980 00:00:00  FSCK0020.REC
   88  6144        Jan 01 1980 00:00:00  FSCK0021.REC
   89  22528       Jan 01 1980 00:00:00  FSCK0022.REC
   90  38912       Jan 01 1980 00:00:00  FSCK0023.REC
   91  34816       Jan 01 1980 00:00:00  FSCK0024.REC
   92  43008       Jan 01 1980 00:00:00  FSCK0025.REC
   93  2048        Jan 01 1980 00:00:00  FSCK0026.REC
   94  26624       Jan 01 1980 00:00:00  FSCK0027.REC
   95  2048        Jan 01 1980 00:00:00  FSCK0028.REC
   96  26624       Jan 01 1980 00:00:00  FSCK0029.REC
   97  2048        Jan 01 1980 00:00:00  FSCK0030.REC

127135744 bytes total (69373952 bytes free)

ciscoasa(config)# show running-config
: Saved
:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.254 inside
dhcpd enable inside
!

threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
!
!
prompt hostname context
Cryptochecksum:cbc2da1e87c4a39814d7e2825121d3e0
: end

ciscoasa(config)# show startup-config
: Saved
: Written by enable_15 at 07:53:10.829 UTC Sun Apr 7 2013
!
ASA Version 8.2(1)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.254 inside
dhcpd enable inside
!

threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
!
!
prompt hostname context
Cryptochecksum:cbc2da1e87c4a39814d7e2825121d3e0

ciscoasa(config)#

share show ssl,

Regards

Julio Carvajal
Senior Network Security and Core Specialist
CCIE #42930, 2xCCNP, JNCIP-SEC


ciscoasa(config)# show ssl
Accept connections using SSLv2, SSLv3 or TLSv1 and negotiate to SSLv3 or TLSv1
Start connections using SSLv3 and negotiate to SSLv3 or TLSv1
Enabled cipher order: rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
Disabled ciphers: des-sha1 rc4-md5 null-sha1
No SSL trust-points configured
Certificate authentication is not enabled

ciscoasa(config)#

Hello Robert,

This should be working by now,

What are you getting on the Java logs???

What java version are you running?

Not sure if we discussed this before, but from the computer can you ping the ASA inside IP address??

Regards

Julio Carvajal
Senior Network Security and Core Specialist
CCIE #42930, 2xCCNP, JNCIP-SEC
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card