cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
493
Views
5
Helpful
4
Replies

ASA 5510, builtin Ports (3 or 5?)

RichardSW
Level 1
Level 1

I have asked multiple vendors and I can't get an answer on this. We're about to buy the ASA 5510. On CDW's site, the base model comes with 3 ports. The 5510 w/ Security Plus license comes with 5 ports.

Now what I need to know, is there an additional module that has to be installed to get those 5 ports, or does the base model already have all 5 (and 2 are just disactivated)?

Thanks!

1 Accepted Solution

Accepted Solutions

jackko
Level 7
Level 7

below is a sample output of "sh ver" of 5510 with base

Cisco Adaptive Security Appliance Software Version 7.0(1)

Device Manager Version 5.0(1)

Compiled on Thu 31-Mar-05 14:37 by builders

System image file is "disk0:/ASA701.bin"

Config file at boot was "startup-config"

ASA-5510-A up 4 days 5 hours

Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 64MB

BIOS Flash AT49LW080: @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

Boot microcode : CNlite-MC-Boot-Cisco-1.2

SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03

IPSec microcode : CNlite-MC-IPSECm-MAIN-2.03

0: Ext: Ethernet0/0 : media index 0: irq 9

1: Ext: Ethernet0/1 : media index 1: irq 9

2: Ext: Ethernet0/2 : media index 2: irq 9

3: Ext: Not licensed : media index 3: irq 9

4: Ext: Management0/0 : media index 4: irq 11

5: Int: Not licensed : media index 0: irq 11

6: Int: Not licensed : media index 5: irq 5

Licensed features for this platform:

Maximum Physical Interfaces : 4

Maximum VLANs : 0

Inside Hosts : Unlimited

Failover : Disabled

VPN-DES : Enabled

VPN-3DES-AES : Enabled

Security Contexts : 0

GTP/GPRS : Disabled

VPN Peers : 50

This platform has a Base license.

Serial Number: JMX0921L03L

Running Activation Key: xxxx

Configuration register is 0x1

Configuration last modified by enable_15 at 07:22:28.233 UTC Wed Jun 15 2005

it indicates that the base license 5510 has all interfaces built-in, but "sotftware-wise" restricted the third ethernet and the management port cannot be used as normal port.

View solution in original post

4 Replies 4

pmccubbin
Level 5
Level 5

Have you tried calling Cisco's Presales Support Team?

These people will have the answer to your question and they are always the first people I call to verify specifications:

1-800-553-6387

Hope they can help.

jackko
Level 7
Level 7

below is a sample output of "sh ver" of 5510 with base

Cisco Adaptive Security Appliance Software Version 7.0(1)

Device Manager Version 5.0(1)

Compiled on Thu 31-Mar-05 14:37 by builders

System image file is "disk0:/ASA701.bin"

Config file at boot was "startup-config"

ASA-5510-A up 4 days 5 hours

Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 64MB

BIOS Flash AT49LW080: @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

Boot microcode : CNlite-MC-Boot-Cisco-1.2

SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03

IPSec microcode : CNlite-MC-IPSECm-MAIN-2.03

0: Ext: Ethernet0/0 : media index 0: irq 9

1: Ext: Ethernet0/1 : media index 1: irq 9

2: Ext: Ethernet0/2 : media index 2: irq 9

3: Ext: Not licensed : media index 3: irq 9

4: Ext: Management0/0 : media index 4: irq 11

5: Int: Not licensed : media index 0: irq 11

6: Int: Not licensed : media index 5: irq 5

Licensed features for this platform:

Maximum Physical Interfaces : 4

Maximum VLANs : 0

Inside Hosts : Unlimited

Failover : Disabled

VPN-DES : Enabled

VPN-3DES-AES : Enabled

Security Contexts : 0

GTP/GPRS : Disabled

VPN Peers : 50

This platform has a Base license.

Serial Number: JMX0921L03L

Running Activation Key: xxxx

Configuration register is 0x1

Configuration last modified by enable_15 at 07:22:28.233 UTC Wed Jun 15 2005

it indicates that the base license 5510 has all interfaces built-in, but "sotftware-wise" restricted the third ethernet and the management port cannot be used as normal port.

Thank you very much!

it's good to learn that the info provided is useful.

according to cisco,

Why should I rate posts?

If you see a post that you think deserves recognition, please take a moment to rate it.

You'll be helping yourself and others to quickly identify useful content -- as determined by members. And you'll be ensuring that people who generously share their expertise are properly acknowledged. As posts are rated, the value of those ratings are accumulated as "points" and summarized on the Member Profile page and on each member's Preferences page.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: