cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
875
Views
6
Helpful
10
Replies

asa interface route-map to change route metric

hi,

 

can I use route map on interface to chane metric for some route? something like

route-map blabla

match some_acl

set metric 100000

interface some_interface

policy-route route-map blabla

 

so for some network contained in some_acl I want to change metric when it is redistributed to rest of the network via eigrp.

1 Accepted Solution

Accepted Solutions

Use two line in route-map as I mention above

First one match prefix that you want to modify it metric with set command 

Second line match any prefix without any set command 

MHM

View solution in original post

10 Replies 10

I think Yes you  can use route-map when you redistribute static route into eigrp.

You need to use route-map with redistrubte under bgp

And it have two lines 

1- line for prefix you want to set metric 

2-line for prefix that use it defualt metric 

Try this way

Goodluck 

MHM

liviu.gheorghe
Spotlight
Spotlight

Hello @DraganSkundric87318 ,

you can change the metric of a route using a route-map, but not in the way you wrote it.

The route-map is correct, but you will have to use it in the redistribution of a routing protocol into another routing protocol:

ciscoasa(config)# route outside 10.1.1.0 255.255.255.0 192.168.1.1
ciscoasa(config-route-map)# access-list mymap2 line 1 permit 10.1.1.0 255.255.255.0
ciscoasa(config-route-map)# route-map mymap2 permit 10
ciscoasa(config-route-map)# match ip address mymap2
ciscoasa(config-route-map)# router eigrp 1
ciscoasa(config-router)# redistribute static metric 250 250 1 1 1 route-map mymap2

The policy-route route-map interface command configures policy routing or PBR, which means routing by other rules and not by looking at the routing table.

You can find a more detailed explanation about the use of route maps here: https://www.cisco.com/c/en/us/td/docs/security/asa/asa94/config-guides/cli/general/asa-94-general-config/routes-maps.html

Regards, LG
*** Please Rate All Helpful Responses ***

problem is I already have redistribution route map from static to eigrp for some other routes. And I need several routes to be redistributet with modified metric. And it is not possible to have two redistristribution static to eigrp

Use two line in route-map as I mention above

First one match prefix that you want to modify it metric with set command 

Second line match any prefix without any set command 

MHM

You will have a route-map as follows:

ciscoasa(config-route-map)# route-map mymap2 permit 10
ciscoasa(config-route-map)# match ip address mymap2
ciscoasa(config-route-map)# route-map mymap2 permit 20

The first route-map entry will match the routes you want to modify the metric and the second route-map entry will match all the rest of the routes.

Regards, LG
*** Please Rate All Helpful Responses ***

so, for example 

route-map test permit 10
match ip addr acl_default
route-map test permit 20
match ip addr acl_250
set metric 250 250 1 1 1

redistribute static route-map mymap2

 

only acl_250 networks will be redistributed with changed metrics?

 

No, routes matching acl_default will be distributed with their seed metric and routes matching acl_250 will be redistributed with the change metric - the one configured with set metric.

The seed metric is the one configured with the redistribution command, 250 250 1 1 1 in my example, or configured with the seed metric command.

Regards, LG
*** Please Rate All Helpful Responses ***

this order is wrong 
the subnet (you need to set metric) is always match by first route-map line 
you need to SWAP the order 
make line 10 match ACL_250 set metric 
then line 20 match any ( in router IOS you dont need to match anyting it by default match any prefix not previous match by other UPPER  line)
MHM

well, this example is working ok, at least in GNS. Other side receives route for 3.3.3.3 with defaults and route for 4.4.4.4 with changed metric

 


interface Loopback1
ip address 2.2.2.1 255.255.255.255
!
interface FastEthernet0/0
ip address 1.1.1.1 255.255.255.252
duplex auto
speed auto
!

router eigrp 1
redistribute static route-map STATIC-TO-EIGRP1
network 0.0.0.0
no auto-summary
!
ip forward-protocol nd
ip route 3.3.3.3 255.255.255.255 Loopback1
ip route 4.4.4.4 255.255.255.255 Loopback1
!
!

ip access-list standard LISTA1
permit 3.3.3.3
ip access-list standard LISTA2
permit 4.4.4.4
!

route-map STATIC-TO-EIGRP1 permit 10
match ip address LISTA1
!
route-map STATIC-TO-EIGRP1 permit 20
match ip address LISTA2
set metric 1 10000 1 255 1500
!
!
!

UNUTRA#sh ip route 4.4.4.4
Routing entry for 4.4.4.4/32
Known via "eigrp 1", distance 170, metric 2562585600, type external
Redistributing via eigrp 1
Last update from 1.1.1.1 on FastEthernet0/0, 00:06:21 ago
Routing Descriptor Blocks:
* 1.1.1.1, from 1.1.1.1, 00:06:21 ago, via FastEthernet0/0
Route metric is 2562585600, traffic share count is 1
Total delay is 101000 microseconds, minimum bandwidth is 1 Kbit
Reliability 1/255, minimum MTU 1500 bytes
Loading 255/255, Hops 1

UNUTRA#sh ip route 3.3.3.3
Routing entry for 3.3.3.3/32
Known via "eigrp 1", distance 170, metric 409600, type external
Redistributing via eigrp 1
Last update from 1.1.1.1 on FastEthernet0/0, 00:16:52 ago
Routing Descriptor Blocks:
* 1.1.1.1, from 1.1.1.1, 00:16:52 ago, via FastEthernet0/0
Route metric is 409600, traffic share count is 1
Total delay is 6000 microseconds, minimum bandwidth is 10000 Kbit
Reliability 255/255, minimum MTU 1500 bytes
Loading 1/255, Hops 1

UNUTRA#

 

it Work in previous order but each time you need to add prefix to your FW you need to include it in #match ip address LISTA1#

instead change the order make the default in end and match any 
this make route-map check Line-1 ACL for prefix need to modify if not match then will check Line-2 ACL which permit any 

we need to make simple to us 
MHM

Review Cisco Networking for a $25 gift card