Is the SFR module on an 5516X ASA considered an FTD? Reason I ask is that I have FMCv v7.0.1 managing ASA 9.16 devices that have V7.01 Firepower code installed. The option to upgrade to Snort3 seems to be available but documentation says Snort3 is on...
We have two 1140 FTDs that we manage with a FMCv. Both are running version 7.0.5. This may sound like a simple question but I cant seem to figure it out. I created an eem event and after it ran it left a log file in the flash drive of the FTD it ran ...
Hello All, We have Cisco FTD pair configured with HA. Recently we have updated the FTD with 7.0.5 version with this we have also upgraded snort-2 to snort-3 (as per recommendation). Both the requirement has been completed properly. But .. Post than a...
Hisee image belowI was planning on upgrading to 7.05 which looks now to be cisco reccomended version, but after double checking the matrix it seems that thats not an option as if I upgrade FMC to 7.05 it wont be able to manage the FTD's, version 7.2 ...
Looks URL filtering was enabled on a policy with different categories like Gambling blocked but unfortunately few of them are still accessible. I gone through some Cisco document, it's mentioned that https inspection for url filtering only works for ...
Hello , I have received these sort of alert on couple of FTD in a cluster and trying to figure what these mean and ways to address this. it on 9300 firepower module. If anyone have gone through and can share would be highly appreciated Health Moni...
Dear All, I want to reboot FTD Chassis . I would like to know the command to perform the Operation and impact on FTD/Chassis/ Production.Please help this is urgent!
Hi Team,We have got new Cisco Firepower FPR 1120 which is the replacement FTD for our ASA 5545. We need to configure the FTD as same as ASA. ASA do not have any Mgmt interface configured. So we need to manage the LAN interface of FTD as the Mgmt inte...
Hello. I want to know it is OK that Firepower 1010 doesn't communicate with license server. My Firepower 1010 is FTD. It is managed by FDM, only have Base license so I only need to maintain Firepower1010's deployment function. I already registered Fi...
Hello, I have this strange issue on a firepower sensor running version 5.4 and managed by FMC 5.4.1.11. I understand it is end-of-life and end of support but we are in a situation that enforced that we address this issue with the existing set up. Thi...
Hi all,Can someone please tell me how to unassign IP from interface using FTD cli. I made a mistake and I assigned an IP to the Management interface and now I can get to the gui for my FRP1010.I need please the cli to take off the IP and put back to ...
Hello Community, Whilst preparing for a 4110 FTD upgrade via FMC, the readiness check fails.The log files should be located here:Status Log:Readiness Check To x.x.x.x Failure Logs@ /ngfw/var/log/sf/Cisco_FTD_SSP_Patch-6.2.3.18/upgrade_readiness The n...
I am using FTD 1120 using Firepower Device Manager, please advise on the easiet method to set these settingsI need to set the followinga) SSH timeoutb) Console timeoutc) SNMP settingsd) Login Banner
Hello - I have FTD 1010 managed locally. I would like to connect it to CDO, the base license is already active for the FTD (attached). I'm not sure if I need any other license to manage the device from a cloud (CDO).
I have an on-prem FMC that manages a handful of FTD devices. All of these devices use private IPs and are not NATed or exposed to the Internet in any way. The problem is some of the FTD devices are reachable only via IPSec VPN which sometimes gives...
