08-24-2011 01:26 PM - edited 03-11-2019 02:16 PM
Hi all..
I'm having a problem with an ASA firewall..
When i web browse to the ASA i get the certificate warning page, when i click to continue to the website it loads the normal "this page cannot be displayed"..
I use to have the ASDM software on my computer to manage the device however its been uninstalled now.. can this be downloaded somewhere?
i have already tried upgrading the asdm and asa files on the asa?
any ideas?
cheers for any help in advance!
Gerard
Solved! Go to Solution.
08-29-2011 01:38 AM
Hi,
As you can see:
EBEASA# show run asdm
asdm image disk0:/asdm-61551.bin
147 16280544 Aug 24 2011 19:35:46 asdm-645.bin
is not correct, you first need to do:
no asdm image disk0:/asdm-61551.bin
and then:
asdm image disk0:/asdm-645.bin
and then try to access, it should work fine.
Thanks,
Varun
08-24-2011 03:05 PM
Hi,
If you have CLI access we need the following commands:
sh run asdm
sh flash
sh version
It seems like you dont have a valid image of ASDM on flash to start ASDM.
Let me know.
Mike
08-29-2011 01:30 AM
Hi Mike,
Thanks very much for getting back to me!
I have copying across a new asdm file to flash, i rebooted the firewall and tested and i was still unable to access it.
Have a look a the commands below
EBEASA# show run asdm
asdm image disk0:/asdm-61551.bin
asdm location EastBelfast 255.255.255.0 Inside
asdm location VoiceServer 255.255.255.255 Inside
asdm location CityEastServer 255.255.255.255 Inside
asdm location 86.17.10.84 255.255.255.255 Inside
asdm location UPC-Server-One 255.255.255.255 Inside
no asdm history enable
EBEASA# sh flash
--#-- --length-- -----date/time------ path
75 8192 Jan 15 2009 12:03:28 log
79 8192 Aug 30 2008 14:46:14 crypto_archive
148 13934592 Aug 24 2011 20:08:27 asa805-k8.bin
146 89 May 19 2009 13:25:30 dap.xml
147 16280544 Aug 24 2011 19:35:46 asdm-645.bin
255426560 bytes total (224731136 bytes free)
EBEASA# sh ver
Cisco Adaptive Security Appliance Software Version 8.0(4)
Compiled on Thu 07-Aug-08 20:53 by builders
System image file is "disk0:/asa804-k8.bin"
Config file at boot was "startup-config"
EBEASA up 4 days 13 hours
Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Ext: Ethernet0/0 : address is 0022.557e.ac6c, irq 9
1: Ext: Ethernet0/1 : address is 0022.557e.ac6d, irq 9
2: Ext: Ethernet0/2 : address is 0022.557e.ac6e, irq 9
3: Ext: Ethernet0/3 : address is 0022.557e.ac6f, irq 9
4: Ext: Management0/0 : address is 0022.557e.ac6b, irq 11
5: Int: Not used : irq 11
6: Int: Not used : irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 100
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 250
WebVPN Peers : 2
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5510 Security Plus license.
Configuration register is 0x1
Configuration has not been modified since last system restart.
Thanks for having a look Mike!
Anyone else have any ideas too?
Thanks
Gerard
08-29-2011 01:38 AM
Hi,
As you can see:
EBEASA# show run asdm
asdm image disk0:/asdm-61551.bin
147 16280544 Aug 24 2011 19:35:46 asdm-645.bin
is not correct, you first need to do:
no asdm image disk0:/asdm-61551.bin
and then:
asdm image disk0:/asdm-645.bin
and then try to access, it should work fine.
Thanks,
Varun
08-29-2011 01:41 AM
Just for future use, you can use these docs:
http://www.cisco.com/en/US/docs/security/asa/compatibility/asamatrx.html
and also image upgrade:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008067e9f9.shtml
Hope this was helpful.
Thanks,
Varun
08-29-2011 01:49 AM
Hurray!!!
Thanks a million.. done this and it has worked!
Thanks again!
08-29-2011 01:57 AM
Glad it worked
Thanks,
Varun
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide