CISCO ASA 5510 CONFIG PROBLEM!

[antrikos_kal]

Hello, i turned on afte a few weeks and it doesn't see internet.here's the show run

ciscoasa# show run
: Saved
:
: Serial Number: JMX1225L1LS
: Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
:
ASA Version 9.1(7)32
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Ethernet0/0
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.0.0.2 255.255.255.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
!
boot config disk0:/startup-1.cfg
ftp mode passive
pager lines 24
mtu outside 1500
mtu inside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
no snmp-server location
no snmp-server contact
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpoint _SmartCallHome_ServerCA
no validation-usage
crl configure
crypto ca trustpool policy
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd dns 208.67.222.222 208.67.220.220
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
!
!
prompt hostname context
call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email callhome@cisco.com
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:adfe96de0173c0b922d5ee0831e5639e
: end
ciscoasa#

i must say that i havent changed anything and tried to copy the backup config from the flash.what's wrong?i use opendns.

[antrikos_kal]

if that helps you a cable from the router goes to one switch then a cable to another switch and a cable from switch to outside of the asa, the inside of asa comes from the 2nd switch.i haven't changed anything in the hardware conf it takes ips via dhcp from router.

[Rob Ingram]

You've not provided the information I asked for, this will help me determine where the issue may lie.

I am not interested in how the laptop receives the IP address, I want to confirm whether they have the correct default gateway and whether they have the correct DNS settings.

Can the client computers ping 10.0.0.69?

[antrikos_kal]

yes it successfuly pings 10.0.0.69

[antrikos_kal]

anyway because it's too late in Greece, can you please tell me how to reset to factory defaults?i will start from the scratch in the morning.

[antrikos_kal]

w/ the following config i  did from scratch it says and sees network but no internet access.

asa(config)# show run
: Saved
:
: Serial Number: JMX1225L1LS
: Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
:
ASA Version 9.1(7)32
!
hostname asa
domain-name cisco.com
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Ethernet0/0
duplex full
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/1
duplex full
nameif inside
security-level 100
ip address 10.1.1.1 255.255.255.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
management-only
shutdown
nameif management
security-level 100
no ip address
!
ftp mode passive
dns server-group DefaultDNS
domain-name cisco.com
object network inside
subnet 10.0.0.0 255.255.255.0
pager lines 24
logging asdm informational
mtu management 1500
mtu outside 1500
mtu inside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
!
object network inside
nat (inside,outside) dynamic interface
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.1.1.2 255.255.255.255 management
no snmp-server location
no snmp-server contact
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd dns 208.67.222.222 208.67.220.220
dhcpd ping_timeout 750
!
dhcpd address 10.1.1.32-10.1.1.63 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
call-home reporting anonymous prompt 2
Cryptochecksum:f8ae89ad8584caafbfa764f831ee49c2
: end
asa(config)#

[antrikos_kal]

it is a dns issue, windows 10 network diagnostics says about it.what should i do or i forgot to do?

[Rob Ingram]

You've change the inside network again, so your nat rule would not work. You need to amend the nat rule to this:

object network inside
subnet 10.1.1.0 255.255.255.0

Have you confirmed the default gateway on the client devices is actually the correct IP address (10.1.1.1)?

If it is you should see the counters increase on the NAT rule and hopefully have internet access (once you've made the change above).

[antrikos_kal]

HI!

the commands i need to type are the following which are deprecated, i need you to tell me the equivalent ones

nat (inside) 1ips ips 

global (outside) 1 interface

[antrikos_kal]

i did the 

object network inside
subnet 10.1.1.0 255.255.255.0

but i see ethernet takes ips from the royter the outside but not internet access.

[antrikos_kal]

asa# show run
: Saved
:
: Serial Number: JMX1225L1LS
: Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
:
ASA Version 9.1(7)32
!
hostname asa
domain-name cisco.com
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Ethernet0/0
duplex full
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/1
duplex full
nameif inside
security-level 100
ip address 10.1.1.2 255.0.0.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
management-only
shutdown
nameif management
security-level 100
no ip address
!
boot config disk0:/startup-1.cfg
ftp mode passive
dns server-group DefaultDNS
domain-name cisco.com
object network inside
subnet 10.1.1.0 255.255.255.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.1.1.1 255.255.255.255 management
no snmp-server location
no snmp-server contact
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd dns 195.170.0.2 195.170.2.1
dhcpd ping_timeout 750
!
dhcpd address 10.1.1.32-10.1.1.63 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:62a0d860ea3f96500acf2acb9bd236ab

[antrikos_kal]

the gateway must be the router 192.168.1.1 or the outside of the asa? cause i think i setted up 10.1.1.1 and if so how do i change it?

[antrikos_kal]

can you help please?

ciscoasa# show run
: Saved
:
: Serial Number: JMX1225L1LS
: Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
:
ASA Version 9.1(7)32
!
hostname ciscoasa
domain-name cisco.com
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Ethernet0/0
duplex full
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/1
duplex full
nameif inside
security-level 100
ip address 10.1.1.2 255.0.0.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
duplex full
management-only
nameif management
security-level 100
no ip address
!
boot config disk0:/startup-1.cfg
ftp mode passive
dns server-group DefaultDNS
domain-name cisco.com
object network inside
subnet 10.1.1.0 255.255.255.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.1.1.1 255.255.255.255 management
no snmp-server location
no snmp-server contact
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd dns 208.67.222.222 208.67.220.220
dhcpd ping_timeout 750
!
dhcpd address 10.1.1.32-10.1.1.63 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:52e8ec634ffb10d2522751cb6cb23513
: end
ciscoasa#

still no internet.

[antrikos_kal]

all happened after i reseted the password!it was working ok!

[antrikos_kal]

I found the solution it's the command route outside 0.0.0.0 0.0.0.0 but i can't remember the complete command.anyone?

[antrikos_kal]

i used to use nat (inside)1 10.1.1.0 255.255.255.0 and global (outside) 1 interface but they don't work anymore.anyone please?