Create a firewall rule on Cisco 2901

Teknisk04977 · ‎09-10-2019

Hi,

We have the following on a Cisco 2901:

Current configuration : 1999 bytes
!
version 15.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Sky-GW01
!
boot-start-marker
boot-end-marker
!
!
enable secret 5 xxxxxxxxxxxxxxxxxxxxxxx
enable password xxxxxxxxx
!
aaa new-model
!
!
aaa authentication login default none
aaa authentication login VTY enable
!
!
!
!
!
aaa session-id common
clock timezone GMT 1 0
clock summer-time GMT recurring 1 Sun Apr 3:00 last Sun Oct 3:00
!
!
!
!
!
!
!
!
!
!
!
!
!
!
ip domain name domain.no
ip name-server 8.8.8.8
ip name-server 8.4.4.8
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
!
cts logging verbose
!
!
license udi pid CISCO2901/K9 sn FCZ1927C25G
!
!
!
redundancy
!
!
ip ssh authentication-retries 2
ip ssh version 2
ip ssh pubkey-chain
username admin
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
description # Linknet #
ip address 1.1.1.138 255.255.255.248
duplex auto
speed auto
no mop enabled
!
interface GigabitEthernet0/1
description # mydesc #
no ip address
duplex auto
speed auto
!
interface GigabitEthernet0/1.10
encapsulation dot1Q 10
ip address 2.2.2.193 255.255.255.192
!
interface GigabitEthernet0/1.50
encapsulation dot1Q 50
ip address 2.2.2.129 255.255.255.192 secondary
ip address 2.2.2.1 255.255.255.128
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip route 0.0.0.0 0.0.0.0 3.3.3.3
!
ip access-list standard SSH
permit 2.2.2.0 0.0.0.255
!
!
!
snmp-server community public RO
snmp-server community private RW
!
!
!
control-plane
!
!
!
line con 0
privilege level 15
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
access-class SSH in
privilege level 15
logging synchronous
login authentication VTY
transport input ssh
!
scheduler allocate 20000 1000
!
end

-------

We want to block all incoming and outgoing traffic to both interfaces, interface GigabitEthernet0/1.10 and GigabitEthernet0/1.50.

In addition we want to allow for ports 3389, 60123 and ping. We also want to allow all traffic to and from both the interfaces internally.

How would we set this up in an easy way? (Ip's are not real, just replaced with 1s and 2s)

Thank you :)

johnd2310 · ‎09-10-2019

Hi,

You need to clarify your requirements a bit.

Do you want 0/1.10 and 0/1.50 to be able to talk to each other but should not be able to talk to 0/0 except on ports 3389, 60123 and ping?

Thanks

John

**Please rate posts you find helpful**

Teknisk04977 · ‎09-11-2019

Well, basically 0/1.10 and 0/1.50 should allow all traffic OUT to the internet. And they should allow 3389,60123 incoming ports open. Internal traffic between 0/1.10 and 0/1.50 both IN And OUT should be open. I'm not sure what 0/0 does really, isn't that the route out to internet?