cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1478
Views
0
Helpful
2
Replies

CSM 4.4 Discovery Error ASA 9.1.4

Hello,

I always get error discovering asa 5505, it stop at 24% on reading and parsing device config step. Here is the sh ver,

Cisco Adaptive Security Appliance Software Version 9.1(1)4

Device Manager Version 7.1(2)

Compiled on Wed 13-Mar-13 07:45 by builders

System image file is "disk0:/asa911-4-k8.bin"

Config file at boot was "startup-config"

firewall up 13 mins 37 secs

Hardware:   ASA5505, 512 MB RAM, CPU Geode 500 MHz,

Internal ATA Compact Flash, 128MB

BIOS Flash M50FW016 @ 0xfff00000, 2048KB

Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)

                             Boot microcode        : CN1000-MC-BOOT-2.00

                             SSL/IKE microcode     : CNLite-MC-SSLm-PLUS-2.03

                             IPSec microcode       : CNlite-MC-IPSECm-MAIN-2.08

                             Number of accelerators: 1

0: Int: Internal-Data0/0    : address is e4d3.f193.a130, irq 11

1: Ext: Ethernet0/0         : address is e4d3.f193.a128, irq 255

2: Ext: Ethernet0/1         : address is e4d3.f193.a129, irq 255

3: Ext: Ethernet0/2         : address is e4d3.f193.a12a, irq 255

4: Ext: Ethernet0/3         : address is e4d3.f193.a12b, irq 255

5: Ext: Ethernet0/4         : address is e4d3.f193.a12c, irq 255

6: Ext: Ethernet0/5         : address is e4d3.f193.a12d, irq 255

7: Ext: Ethernet0/6         : address is e4d3.f193.a12e, irq 255

8: Ext: Ethernet0/7         : address is e4d3.f193.a12f, irq 255

9: Int: Internal-Data0/1    : address is 0000.0003.0002, irq 255

10: Int: Not used            : irq 255

11: Int: Not used            : irq 255

Licensed features for this platform:

Maximum Physical Interfaces       : 8              perpetual

VLANs                             : 3              DMZ Restricted

Dual ISPs                         : Disabled       perpetual

VLAN Trunk Ports                  : 0              perpetual

Inside Hosts                      : 50             perpetual

Failover                          : Disabled       perpetual

Encryption-DES                    : Enabled        perpetual

Encryption-3DES-AES               : Enabled        perpetual

AnyConnect Premium Peers          : 2              perpetual

AnyConnect Essentials             : Disabled       perpetual

Other VPN Peers                   : 10             perpetual

Total VPN Peers                   : 12             perpetual

Shared License                    : Disabled       perpetual

AnyConnect for Mobile             : Disabled       perpetual

AnyConnect for Cisco VPN Phone    : Disabled       perpetual

Advanced Endpoint Assessment      : Disabled       perpetual

UC Phone Proxy Sessions           : 2              perpetual

Total UC Proxy Sessions           : 2              perpetual

Botnet Traffic Filter             : Disabled       perpetual

Intercompany Media Engine         : Disabled       perpetual

Cluster                           : Disabled       perpetual

This platform has a Base license.

Serial Number: xxxxxxxxxxx

Running Permanent Activation Key: xxxxxxxxx xxxxxxxxx xxxxxxxxx xxxxxxxxx

Configuration register is 0x1

Configuration has not been modified since last system restart.

1 Accepted Solution

Accepted Solutions

The ASA crashed when CSM ran the 'show inventory' command. This is  caused by a known bug:

CSCud20887 - ASA reloads after issuing "show inventory" command

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCud20887

You can download 9.1(2) from cisco.com, which has the fix for this bug:

http://software.cisco.com/download/release.html?mdfid=280582808&flowid=4377&softwareid=280775065&release=9.1.2.ED&relind=AVAILABLE&rellifecycle=&reltype=latest

View solution in original post

2 Replies 2

The ASA crashed when CSM ran the 'show inventory' command. This is  caused by a known bug:

CSCud20887 - ASA reloads after issuing "show inventory" command

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCud20887

You can download 9.1(2) from cisco.com, which has the fix for this bug:

http://software.cisco.com/download/release.html?mdfid=280582808&flowid=4377&softwareid=280775065&release=9.1.2.ED&relind=AVAILABLE&rellifecycle=&reltype=latest

Thanks for posting the resolution to your issue. It helps the quality of the forum's content.

Review Cisco Networking for a $25 gift card