07-28-2008 05:31 AM - edited 02-21-2020 02:56 AM
Hi,
How would one go about setting the 1000Mbps speed to a ASA 5510 with the "security plus" license?
This is what I'm getting on any interface:
fw(config-if)# speed ?
interface mode commands/options:
10 Force 10 Mbps operation
100 Force 100 Mbps operation
auto Enable AUTO speed configuration
Thanks.
Gabi
Solved! Go to Solution.
07-29-2008 10:08 PM
I thhink you should upgrede to 8.0(3)
I have asa 5510 with security plus license.
Cisco Adaptive Security Appliance Software Version 7.2(3)
ASA5510(config-if)#
ASA5510# conf t
ASA5510(config)# int e0/0
ASA5510(config-if)# spe
ASA5510(config-if)# speed ?
interface mode commands/options:
10 Force 10 Mbps operation
100 Force 100 Mbps operation
1000 Force 1000 Mbps operation
auto Enable AUTO speed configuration
07-28-2008 05:55 AM
hi,
please post output of the command
"show int ip bri"
07-28-2008 06:20 AM
with the sec+ license, only interfaces 0 and 1 are gig enabled. the others are only 10/100.
http://www.cisco.com/en/US/products/ps6120/prod_models_comparison.html
07-29-2008 02:25 AM
... and still I can't set eighter e0/0 or e0/1 to gigabit.
07-29-2008 02:23 AM
fw(config)# sh int ip bri
Interface IP-Address OK? Method Status Protocol
Ethernet0/0 xxx.xxx.xxx.xxx YES CONFIG up up
Ethernet0/1 xxx.xxx.xxx.xxx YES CONFIG up up
Ethernet0/2 unassigned YES unset administratively down down
Ethernet0/3 unassigned YES unset administratively down down
Management0/0 unassigned YES unset administratively down down
07-29-2008 03:37 AM
Beginning with Cisco ASA Software v7.2.3, the ASA 5510 Security Plus license enables 2 10/100/1000 interfaces and 3 10/100 interfaces
What Cisco ASA Software do you have?
07-29-2008 09:30 PM
Yes, I know about that, thank you.
I have version 8.0(2), Security Plus license.
Do any of you know how this works - it's set automatically to 1Gbps or do you need to set it.
Thanks.
07-29-2008 10:08 PM
I thhink you should upgrede to 8.0(3)
I have asa 5510 with security plus license.
Cisco Adaptive Security Appliance Software Version 7.2(3)
ASA5510(config-if)#
ASA5510# conf t
ASA5510(config)# int e0/0
ASA5510(config-if)# spe
ASA5510(config-if)# speed ?
interface mode commands/options:
10 Force 10 Mbps operation
100 Force 100 Mbps operation
1000 Force 1000 Mbps operation
auto Enable AUTO speed configuration
07-29-2008 10:11 PM
Is this a known bug?
Given that I have a version higher that 7.2(3) I should have this option too...
07-30-2008 07:12 AM
Its not a 'bug'. Cisco maintains multiple versions at once 7.0.x 7.2.x 8.0.x etc. So it doesnt mean 7.2(3) is older than 8.0(2).
Regards
Farrukh
10-19-2008 11:21 PM
I've upgraded to 8.0(4). Now it works although there is no mention in the release notes about this.
Thanks!
Gabi
10-19-2008 11:30 PM
Thanks for the update and I'm glad you have it working now :).
But I just checked the release notes and its mentioned there albeit in a slightly covert manner :)
CSCsl53995
5510 interface can be set to1000Mbps with base license
Regards
Farrukh
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide