I need to DMZ access to internet and see the inside on ASA 5520

[josue jonathan rivero herrera]

Hi everyone.

I am new in ASA, I have the DMZ (10.1.1.0/24) configured on ASA 5520 and I achieve the reach Internet from DMZ (10.1.1.0/24), but now need reach DMZ from inside (172.16.12.0/24) and inside (172.16.12.0/24) from DMZ  (10.1.1.0/24), in other words round trip.

ths show run is attached.

I try with the next links, but dont work.

https://supportforums.cisco.com/thread/2018253

https://supportforums.cisco.com/thread/2045888

thk for help me !!!

BR

[Marvin Rhoads]

Since the DMZ is lower security level than inside, you must create and apply and access-list to allow DMZ-originated traffic to access inside addresses.

Something like:

access-list DMZ_IN extended permit

access-group DMZ_IN in interface DMZ

Inside to DMZ will automatically work (unless you start ACLing in in which case an implicit deny will be added at the end).

If you're new to the ASA, I recommend you use ASDM to create your changes. Set it to preview commands and look at what it generates to understand the CLI.

[josue jonathan rivero herrera]

hi Marvin.

I try with ASDM but I do not like, I think that is better with CLI.

I try with you tell me later, i think that this help me.

access-list DMZ_IN permit 10.1.1.0 255.255.255.0 172.16.12.0 255.255.255.0
access-list DMZ_IN permit 10.1.1.0 255.255.255.0 172.16.6.0 255.255.255.0

access-group DMZ_IN permit in interface DMZ

static (inside,DMZ) 10.1.1.0 10.1.1.0 netmask 255.255.255.0

you tihink that this help me?

BR and THK!!!

[Marvin Rhoads]

Yes, what you have proposed looks good.

[josue jonathan rivero herrera]

ok, let me try out production and update you.

:-)

[josue jonathan rivero herrera]

Hi Marvin,

Apologies for the delay but too much work here, I try with the next command.

access-list DMZ_IN extended permit tcp 10.1.1.0 255.255.255.0 172.16.12.0 255.255.255.0

access-list DMZ_IN extended permit udp 10.1.1.0 255.255.255.0 172.16.12.0 255.255.255.0

access-list DMZ_IN extended permit tcp 10.1.1.0 255.255.255.0 172.16.6.0 255.255.255.0

access-list DMZ_IN extended permit udp 10.1.1.0 255.255.255.0 172.16.6.0 255.255.255.0

access-group DMZ_IN in interface DMZ

nat (DMZ) 1 0.0.0.0 0.0.0.0

static (inside,DMZ) 10.1.1.0 10.1.1.0 netmask 255.255.255.0

and when I configure the PC with DGW (interface DMZ`s firewall) I don't reach the LAN but Internet is reachable, i need to reach both (LAN-172.16.12.0, 172.16.6.0 and Internet).

do you have someone idea for help me?

thk so much!!!

[Marvin Rhoads]

Try using packet-tracer on the ASA to follow the logic through the box and determine why your DMZ-Inside traffic isn't working.

packet-tracer input dmz detailed

The output should tell you why the packets aren't flowing.