04-11-2011 06:25 AM - edited 02-21-2020 04:18 AM
Hi all,
I have a rpoblem with a specific client with LMS 3.2. We are using LMS 3.2 on Windows 2008 and everything seem to be working OK. The issue is in the CiscoView with the 4500 switches. CiscoView can see the supervisors on all 4500 switches (6); but cannot see the switchcards when the switchcards are WS-X4648-RJ45-E. Find the sh inv output below:
CSR-D1#sh inventory
NAME: "Switch System", DESCR: "Cisco Systems, Inc. WS-C4507R-E 7 slot switch "
PID: WS-C4507R-E , VID: V01, SN: FOX1152GKR1
NAME: "Clock Module", DESCR: "Clock Module"
PID: WS-X4K-CLOCK-E , VID: V01, SN: JAE120354DD
NAME: "Linecard(slot 1)", DESCR: "10/100/1000BaseT (RJ45) with 48 10/100/1000 baseT "
PID: WS-X4648-RJ45-E , VID: V01, SN: JAE14410NLT
NAME: "Linecard(slot 2)", DESCR: "6 Dual media SFP or 10/100/1000BaseT (RJ45)V voice power ports (Cisco/IEEE)"
PID: WS-X4506-GB-T , VID: V05, SN: JAE120351NC
NAME: "Linecard(slot 3)", DESCR: "Supervisor 6-E 10GE (X2), 1000BaseX (SFP) with 2 10GE X2 ports"
PID: WS-X45-SUP6-E , VID: V01, SN: JAE120576HG
NAME: "TenGigabitEthernet3/1", DESCR: "10Gbase-LRM"
PID: FTLX1341E2-C1 , VID: A , SN: FNS1352175M
NAME: "TwinGig Converter 3/2", DESCR: "TwinGig Converter Module"
PID: 800-27645-01 , VID: A0 , SN: CAT1147H2WK
NAME: "Linecard(slot 4)", DESCR: "Supervisor 6-E 10GE (X2), 1000BaseX (SFP) with 2 10GE X2 ports"
PID: WS-X45-SUP6-E , VID: V07, SN: JAE14080NL2
NAME: "TwinGig Converter 4/2", DESCR: "TwinGig Converter Module"
PID: 800-27645-01 , VID: A0 , SN: CAT1147H2BV
NAME: "Linecard(slot 7)", DESCR: "10/100/1000BaseT (RJ45) with 48 10/100/1000 baseT "
PID: WS-X4648-RJ45-E , VID: V01, SN: JAE14420A2F
I have updated the s/w to 12.2(53) SG1 with no luck.
Solved! Go to Solution.
06-09-2011 04:04 AM
Thanks.
I installed this package and cards are now seen in CiscoView.
But I got a small problem.
The drawing of WS-X4624-SFP-E and WS-4648-RJ45-E appears with white vertical lines and my customer doesn't like this.
Do you have the same problem ?
Patrice
04-15-2011 02:00 AM
Hi Nicos,
I have exactly the same issue with LMS 3.2 CiscoView under Windows 2003 and catalyst switch 4506-E.
4506-E are in IOS 12.2(53)SG2.
I installed latest 4500IOS V 19.0 ciscoview device package without success.
Did you fix your problem ?
04-15-2011 02:47 AM
No I havent and we are thinking of opening a TAC case. When i have an answer i will let u know.
/n
06-05-2011 10:51 PM
The workaround was to upgrade the device package of CiscoView to the following : Cat4000IOS.cv50.v20-0.zip and the problem was fixed.
06-09-2011 04:04 AM
Thanks.
I installed this package and cards are now seen in CiscoView.
But I got a small problem.
The drawing of WS-X4624-SFP-E and WS-4648-RJ45-E appears with white vertical lines and my customer doesn't like this.
Do you have the same problem ?
Patrice
06-09-2011 06:00 AM
Hello,
No, our seems to be working fine (as far as i know). But the next time i go to the client i will check it and let u know 4 sure.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: