05-18-2013 08:32 PM - edited 03-11-2019 06:45 PM
here is my config, i dont know what is wrong.
Well its in this line but do i have to type in a ip even if comcast is giving me a dhcp address?
route outside 0.0.0.0 0.0.0.0 any 1
=============================
hostname asa1
domain-name mydomain.com
enable password rwt5UQJihEq2/Qae encrypted
names
!
interface Vlan1
description to inside VLAN
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
description to outside interface (DHCP Cablemodem)
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/0
description physical connection to Comcast Cablemodem
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd rwt5UQJihEq2/Qae encrypted
banner motd
banner motd +-------------------------------------------------------------------+
banner motd | |
banner motd | *** Unauthorized Use or Access Prohibited *** |
banner motd | |
banner motd | For Authorized Official Use Only |
banner motd | You must have explicit permission to access or |
banner motd | configure this device. All activities performed |
banner motd | on this device may be logged, and violations of |
banner motd | this policy may result in disciplinary action, and |
banner motd | may be reported to law enforcement authorities. |
banner motd | |
banner motd | There is no right to privacy on this device. |
banner motd | |
banner motd +-------------------------------------------------------------------+
banner motd
!
!
!
!
!
!
ftp mode passive
dns domain-lookup outside
dns server-group DefaultDNS
name-server 4.2.2.2
name-server 75.75.75.75
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_in extended permit icmp any any echo-reply
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
!
object network obj_any
nat (inside,outside) dynamic interface
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 any 1
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication ssh console LOCAL
aaa authentication serial console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh scopy enable
ssh 192.168.1.0 255.255.255.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 5
ssh version 2
console timeout 0
!
!
!
!
!
dhcpd dns 4.2.2.2 75.75.75.75
dhcpd lease 691200
dhcpd ping_timeout 750
dhcpd domain mydomain.com
dhcpd auto_config outside
!
dhcpd address 192.168.1.20-192.168.1.50 inside
dhcpd enable inside
!
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
!
service-policy global_policy global
username admin password J5nTOEDhPTdyBWnI encrypted privilege 15
prompt hostname context
: end
05-19-2013 07:30 AM
Roman,
If your ISP is giving you a Default gateway as well (most common scenario ever when using DHCP), then you dont need the route command, the dhcp set route that you have on the interface should take care of that.
That being said, remove the line (if it is there), grab the show ip and the show route to see if you are getting a route.
Mike Rojas
05-19-2013 10:07 PM
thanks..
i tryed that, at first it didnt go.. turned out there was an issue with my modem registering. its all fixed now. but i also upgraded the asa iso image and that worked with no issues.
as of right now its all working..
really quickly tho, how hard/easy would it be to set up vpn using a dynamic adress from one asa to mine?
05-20-2013 11:11 PM
this might be a dumb question but do i need to have a domain name?
05-21-2013 07:22 AM
If you are generating certificate signing requests for 3rd-party certificates or using ssh, you probably need a domain name. You don't need a domain name just to filter traffic, and you can change the domain name without affecting the ACL's and access-groups.
-- Jim Leinweber, WI State Lab of Hygiene
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide