cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
8546
Views
0
Helpful
21
Replies

Outside to Inside with NAT

Navaz Wattoo
Level 1
Level 1

Hyi have face problem regradin traffic from outside to insdie having applying acl below here

access-list 101 permit ip any any

APPLY on outside interface

access-group 101 in interface outside

but my traffice didnt pass through from outside to indie

Navaz       

Navaz
1 Accepted Solution

Accepted Solutions

Hi

I think that you can use.

View solution in original post

21 Replies 21

can you exactly describe what you want to allow on your ASA? Which is the ASA-version you are running and can the ASA reach the internet and the internal server that you want to expose to the internet? The actual config can also help.

And "permit ip any any" is most likely not what you want to use on a firewall.


Sent from Cisco Technical Support iPad App

Version 8.0(2) and ASA ping both sides (outside to internet and inside to internal network).

Here is the show running configuration

ASA(config)# sh running-config

: Saved

:

ASA Version 8.0(2)

!

hostname ASA

enable password 8Ry2YjIyt7RRXU24 encrypted

names

!

interface Ethernet0/0

nameif outside

security-level 0

ip address 10.1.1.1 255.255.255.0

!

interface Ethernet0/1

nameif inside

security-level 100

ip address 192.168.1.1 255.255.255.0

!

interface Ethernet0/2

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet0/3

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet0/4

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet0/5

shutdown

no nameif

no security-level

no ip address

!

passwd 2KFQnbNIdI.2KYOU encrypted

ftp mode passive

access-list 101 extended permit ip any any

pager lines 24

mtu outside 1500

mtu inside 1500

no failover

icmp unreachable rate-limit 1 burst-size 1

no asdm history enable

arp timeout 14400

nat-control

global (outside) 1 10.1.1.30

nat (inside) 1 192.168.1.0 255.255.255.0

access-group 101 in interface outside

access-group 101 in interface inside

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout uauth 0:05:00 absolute

dynamic-access-policy-record DfltAccessPolicy

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart

no crypto isakmp nat-traversal

telnet timeout 5

ssh timeout 5

console timeout 0

threat-detection basic-threat

threat-detection statistics access-list

!

!

prompt hostname context

Cryptochecksum:a910fcee5200493f2ed21db7bd2f82d6

: end

ASA(config)#

Navaz

Message was edited by: Navaz Wattoo

Navaz

So it's not a real network but learning how to operate the ASA?

You should start with NAT and think about if you really need NAT. In your diagram inside and outside should have full routing reachability, so NAT is not needed.

On the Config-Guide you find all info how NAT works on the ASA:

http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/cfgnat.html

start with the commands "nat", "global" and "nat-control". For your case, all of these can be removed from the config and reachability should be there.

If you want to simulate a situation where the outside interface connects to the internet you need to configure a ststic translation and you should keep the "nat" and "global". The additional config you need is a "static" command.

After that go over to the configuration of access-control:

http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/nwaccess.html

You don't want to allow any traffic into your network.

-- 
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Hi,

Check routing , i dont see any.

- Pankaj

the systems in this scenario are directly connected so there is no need for an extra routing-config. Of course you are right if this would be an internet-connected setup. There at least a default-route would be needed.

-- 
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

linksysinfo
Level 4
Level 4

Have a look here:

http://www.darkmoon.org.uk/173

Regards Simon
http://www.linksysinfo.org

Regards Simon

dfeurt1969
Level 1
Level 1

Hello Navaz,
Along with routing and the ACL, you will also need to have a static xlate configured to allow the inbound traffic. I don't see that in your configuration.

Sent from Cisco Technical Support iPad App

can you please send me the xlate configuration?

Navaz

Navaz

It should look like this:
Static (inside,outside) 192.168.1.0 192.168.1.0 net mask 255.255.255.0

I'm not sure what your topology is, but you will have to be able to route to the 192.168.1.0 network from your outside host(s).

Sent from Cisco Technical Support iPad App

Sorry, no space in the netmask keyword. The iPad auto correct strikes again... :-)

Sent from Cisco Technical Support iPad App

David i am sending you topology and the configuration that i configured.

ASA(config)# sh running-config

: Saved

:

ASA Version 8.0(2)

!

hostname ASA

enable password 8Ry2YjIyt7RRXU24 encrypted

names

!

interface Ethernet0/0

nameif outside

security-level 0

ip address 10.1.1.1 255.255.255.0

!

interface Ethernet0/1

nameif inside

security-level 100

ip address 192.168.1.1 255.255.255.0

!

interface Ethernet0/2

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet0/3

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet0/4

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet0/5

shutdown

no nameif

no security-level

no ip address

!

passwd 2KFQnbNIdI.2KYOU encrypted

ftp mode passive

access-list 101 extended permit ip any any

pager lines 24

mtu outside 1500

mtu inside 1500

no failover

icmp unreachable rate-limit 1 burst-size 1

no asdm history enable

arp timeout 14400

nat-control

global (outside) 1 10.1.1.30

nat (inside) 1 192.168.1.0 255.255.255.0

static (outside,inside) 10.1.1.30 10.1.1.2 netmask 255.255.255.255

access-group 101 in interface outside

access-group 101 in interface inside

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout uauth 0:05:00 absolute

dynamic-access-policy-record DfltAccessPolicy

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart

no crypto isakmp nat-traversal

telnet timeout 5

ssh timeout 5

console timeout 0

threat-detection basic-threat

threat-detection statistics access-list

!

!

prompt hostname context

Cryptochecksum:a910fcee5200493f2ed21db7bd2f82d6

: end

ASA(config)#

Navaz

Navaz

anyone have solution of this?

Navaz

Navaz

what traffic (ports) are you try to let in from outside in and to where?

Regards Simon
http://www.linksysinfo.org

Regards Simon

i need any kind of traffice pass through both side that from inside to outside and outside to inside

Thanks and Regards

Navaz

Navaz
Review Cisco Networking for a $25 gift card