08-13-2018 12:05 AM - edited 02-21-2020 08:05 AM
Hi, guys
I have applied three Rate Limit "Police" into three VLANs ( the configurations are similar ), but only seems the configuration works on VLAN160, others do not work (VLAN1 and VLAN5 ).
Please advice:
-----------------------------------------------
fw# sh service-policy policy
Interface vlan1:
Service-policy: BW_limit
Class-map: BW_Limit_class
Input police Interface vlan1:
cir 800000000 bps, bc 25000000 bytes
conformed 128106140 packets, 173573383902 bytes; actions: transmit
exceeded 0 packets, 0 bytes; actions: drop
conformed 18671240 bps, exceed 0 bps
Output police Interface vlan1:
cir 800000000 bps, bc 25000000 bytes
conformed 35630141 packets, 4896581199 bytes; actions: transmit
exceeded 0 packets, 0 bytes; actions: drop
conformed 524184 bps, exceed 0 bps
Interface vlan5:
Service-policy: BW_limit
Class-map: BW_Limit_class
Input police Interface vlan5:
cir 800000000 bps, bc 25000000 bytes
conformed 1815849092 packets, 2590382179124 bytes; actions: transmit
exceeded 0 packets, 0 bytes; actions: drop
conformed 278687120 bps, exceed 0 bps
Output police Interface vlan5:
cir 800000000 bps, bc 25000000 bytes
conformed 468072504 packets, 27958076238 bytes; actions: transmit
exceeded 0 packets, 0 bytes; actions: drop
conformed 3006288 bps, exceed 0 bps
Interface vlan160:
Service-policy: BW_limit
Class-map: BW_Limit_class
Input police Interface vlan160:
cir 800000000 bps, bc 25000000 bytes
conformed 629467104 packets, 141219394983 bytes; actions: transmit
exceeded 0 packets, 0 bytes; actions: drop
conformed 15185240 bps, exceed 0 bps
Output police Interface vlan160:
cir 800000000 bps, bc 25000000 bytes
conformed 2365892637 packets, 3336616774809 bytes; actions: transmit
exceeded 1374 packets, 1961800 bytes; actions: drop
conformed 358971352 bps, exceed 208 bps
# exit
------------------------------------------------------------------------
Interfaces :
fw# sh int po1
Interface Port-channel1 "vlan1", is up, line protocol is up
Hardware is EtherChannel/LACP, BW 2000 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), 1000 Mbps(1000 Mbps)
Input flow control is unsupported, output flow control is off
Description: OA
MAC address axxc.xxxx.6xxxf, MTU 1500
IP address 10.2.1.4, subnet mask 255.255.255.0
Traffic Statistics for "vlan1":
144492554 packets input, 182340726937 bytes
49640555 packets output, 9067544679 bytes
549264 packets dropped
1 minute input rate 714 pkts/sec, 699262 bytes/sec
1 minute output rate 482 pkts/sec, 101613 bytes/sec
1 minute drop rate, 3 pkts/sec
5 minute input rate 351 pkts/sec, 314188 bytes/sec
5 minute output rate 277 pkts/sec, 63086 bytes/sec
5 minute drop rate, 3 pkts/sec
Members in this channel:
Active: Gi0/2 Gi0/3
fw# sh int po1.5
Interface Port-channel1.5 "vlan5", is up, line protocol is up
Hardware is EtherChannel/LACP, BW 2000 Mbps, DLY 10 usec
VLAN identifier 5
Description: Email
MAC address axxc.xxxx.6xxxc, MTU 1500
IP address 10.2.2.4, subnet mask 255.255.255.0
Traffic Statistics for "vlan5":
3917326632 packets input, 5513349006356 bytes
753042930 packets output, 35121587156 bytes
85755 packets dropped
fw# sh int po1.160
Interface Port-channel1.160 "vlan160", is up, line protocol is up
Hardware is EtherChannel/LACP, BW 2000 Mbps, DLY 10 usec
VLAN identifier 160
Description: Office
MAC address axxc.xxxx.6xxxb, MTU 1500
IP address 10.2.3.4, subnet mask 255.255.255.0
Traffic Statistics for "vlan160":
943833289 packets input, 168141255646 bytes
4487102236 packets output, 6256050322622 bytes
1073830 packets dropped
fw#
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide