ā02-10-2011 11:41 PM - edited ā03-11-2019 12:49 PM
Hello,
We have several catalyst 6509's with SLB and FWSM, after more then 5 years one crashed and we have to upgrade them because of this . Is there some good documentation on this.
Are there also known issues/dependencies with onboard hardware, SLB loadbalancers, 6509 software releases (hopefully some documentation which describes this) See the details of the software (both 6509 and fwsm) and modules below
vas03asd2>sh ver
Cisco Internetwork Operating System Software
IOS (tm) s72033_rp Software (s72033_rp-PK9S-M), Version 12.2(18)SXD3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Thu 09-Dec-04 22:43 by pwade
Image text-base: 0x4002100C, data-base: 0x42318000
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
BOOTLDR: s72033_rp Software (s72033_rp-PK9S-M), Version 12.2(18)SXD3, RELEASE SOFTWARE (fc1)
vas03asd2 uptime is 5 years, 14 weeks, 3 days, 1 hour, 47 minutes
sh mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL09018RVQ
3 4 SLB Application Processor Complex WS-X6066-SLB-APC SAD090101H7
4 6 Firewall Module WS-SVC-FWM-1 SAD090100FV
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAD0903077X
7 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1025SHRP
8 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL09030X46
9 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL09030X47
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0012.d99d.0d78 to 0012.d99d.0d7b 2.0 12.2(14r)S5 12.2(18)SXD3 Ok
3 0012.4373.f274 to 0012.4373.f27b 1.7 4.2(1) Ok
4 0003.e472.5a0c to 0003.e472.5a13 3.0 7.2(1) 2.3(4) Ok
5 0011.21b5.9140 to 0011.21b5.9143 4.1 8.1(3) 12.2(18)SXD3 Ok
7 0005.7447.80fc to 0005.7447.812b 10.3 7.2(1) 8.3(0.156)RO Ok
8 0013.1a0d.a0f0 to 0013.1a0d.a11f 10.1 7.2(1) 8.3(0.156)RO Ok
9 0008.7dce.b9e0 to 0008.7dce.ba0f 10.1 7.2(1) 8.3(0.156)RO Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------- ------------------ ------------ ------- -------
1 Centralized Forwarding Card WS-F6700-CFC SAL09041037 2.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B SAD090305VK 1.1 Ok
5 MSFC3 Daughterboard WS-SUP720 SAD0901054A 2.2 Ok
Mod Online Diag Status
--- -------------------
1 Pass
3 Pass
4 Pass
5 Pass
7 Pass
8 Pass
9 Pass
VT-Firewall# sh ver
FWSM Firewall Version 2.3(4)
FWSM Device Manager Version 4.1(1)
Compiled on Tue 18-Apr-06 20:28 by dalecki
VT-Firewall up 5 years 240 days
Hardware: WS-SVC-FWM-1, 1024 MB RAM, CPU Pentium III 1000 MHz
Flash 2.20 TOSHIBA THNCF128MBA @ 0xc321, 20MB
0: gb-ethernet0: irq 5
1: gb-ethernet1: irq 7
2: ethernet0: irq 11
Licensed Features:
Failover: Enabled
VPN-DES: Enabled
VPN-3DES: Enabled
Maximum Interfaces: 256
Cut-through Proxy: Enabled
Guards: Enabled
URL-filtering: Enabled
Throughput: Unlimited
ISAKMP peers: Unlimited
Security Contexts: 2
This machine has an Unrestricted (UR) license.
Serial Number: SAD090100FV
Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000
Configuration last modified by admin at 11:57:51 Feb 08 2011
Solved! Go to Solution.
ā02-11-2011 05:18 AM
Hi.
You'll find this info in the release notes. here is a link to the multiple FWSM main train releases:
http://www.cisco.com/en/US/products/hw/modules/ps2706/prod_release_notes_list.html
Release notes include upgrade instructions, and dependencies on CAT6K side.
As for SLB side, this should not have any dependencies on the FWSM side, as they don't talk to each other directly. However if the FWSM upgrade requires you to upgrade your CAT6K side, you might want to check the release notes of the SLB module if it's also compatible with this cat6k image.
Regards,
Fadi.
Does this answer your questions? if yes, please mark the thread as answered.
ā02-11-2011 07:12 AM
I'm glad it went well.
would you please mark this thread as resolved :-).
Regards,
Fadi.
ā02-11-2011 05:18 AM
Hi.
You'll find this info in the release notes. here is a link to the multiple FWSM main train releases:
http://www.cisco.com/en/US/products/hw/modules/ps2706/prod_release_notes_list.html
Release notes include upgrade instructions, and dependencies on CAT6K side.
As for SLB side, this should not have any dependencies on the FWSM side, as they don't talk to each other directly. However if the FWSM upgrade requires you to upgrade your CAT6K side, you might want to check the release notes of the SLB module if it's also compatible with this cat6k image.
Regards,
Fadi.
Does this answer your questions? if yes, please mark the thread as answered.
ā02-11-2011 07:03 AM
Thanks very much, my upgrade in our lab succeeded
Jack Kwakman
Tele2 Nederland B.V
From: fadlouni
To: "J.J.M Kwakman"
Date: 02/11/2011 02:18 PM
Subject: New message: "Upgrade 6509 with SLB and
jkwakman,
A new message was posted in the Discussion thread "Upgrade 6509 with SLB
and FSWM":
https://supportforums.cisco.com/message/3291305#3291305
Author : Fadi Adlouni
Profile : https://supportforums.cisco.com/people/fadlouni
Message:
ā02-11-2011 07:12 AM
I'm glad it went well.
would you please mark this thread as resolved :-).
Regards,
Fadi.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide