02-20-2014 07:33 PM - edited 03-11-2019 08:48 PM
Hello Guys,
I am setting up a cisco asa 5505 FW. I can get interent on the FW and i can connect to the vpn client fine and get a address from the vpn pool i created. The only issue is that i cannot reach the inside interface from the VPN pool. Can someone please assist asap.
Below is my current config....
ASA Version 8.2(5)
!
hostname LCCVPN
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
switchport access vlan 2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
<--- More --->
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.4 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group lccvpn
ip address pppoe
!
ftp mode passive
clock timezone FJST 12
object-group network LAN
network-object 10.0.0.0 255.255.255.0
object-group network VPNpool
network-object 10.20.12.0 255.255.255.0
access-list Network-List standard permit 10.0.0.0 255.255.255.0
access-list Network-List1 standard permit 10.0.0.0 255.255.255.0
access-list inside_access_in extended permit ip any any
pager lines 24
logging enable
<--- More --->
logging timestamp
logging trap informational
logging asdm informational
logging permit-hostdown
mtu inside 1500
mtu outside 1500
ip local pool VPNPool 10.20.12.1-10.20.12.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-613.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
route inside 10.0.0.0 255.0.0.0 10.0.0.4 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
<--- More --->
aaa authentication telnet console LOCAL
aaa authorization command LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside
http 192.168.252.0 255.255.255.128 inside
http 10.2.2.0 255.255.255.0 inside
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community *****
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
<--- More --->
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime seconds 28800
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime kilobytes 4608000
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.0.0.0 255.255.255.0 inside
ssh timeout 5
console timeout 5
vpdn group lccvpn request dialout pppoe
vpdn group lccvpn localname navinisp
vpdn group lccvpn ppp authentication pap
vpdn username navinisp password *****
<--- More --->
dhcpd auto_config outside
!
dhcpd address 10.0.0.10-10.0.0.30 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-win-2.3.0254-k9.pkg 1 regex "Windows NT"
svc enable
group-policy SSLVPN internal
group-policy SSLVPN attributes
banner value This is a private system
banner value Access to this computer system is limited to authorised users only.
banner value This authorization must be obtained in writing from the system owner
banner value Unauthorised users may be subject to prosecution under the Crimes
banner value Act or State legislation
banner value
banner value All accesses to this service are logged
banner value All information and details on this system are private,
banner value confidential and must not be disclosed
<--- More --->
vpn-tunnel-protocol svc
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Network-List1
default-domain value tfl.internal
address-pools value VPNPool
group-policy TechM_VPN_SSL internal
group-policy TechM_VPN_SSL attributes
vpn-tunnel-protocol svc
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Network-List1
address-pools value VPNPool
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol webvpn
group-policy VPN-Client internal
group-policy VPN-Client attributes
vpn-tunnel-protocol IPSec
ip-comp enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Network-List1
default-domain value tfl.internal
user-authentication-idle-timeout 30
address-pools value VPNPool
webvpn
svc compression deflate
<--- More --->
username AutikoL password 5lj6NPIi/MYVQYVN encrypted
username AutikoL attributes
vpn-group-policy VPN-Client
vpn-tunnel-protocol IPSec
group-lock value Client-VPN
service-type remote-access
username admin password f3UhLvUj1QsXsuK7 encrypted
username infra password /l3N1ysL5h1bzNBn encrypted privilege 15
username Shoebh password 9MMH3XLR8ARsN5Cf encrypted
username Shoebh attributes
vpn-group-policy SSLVPN
service-type remote-access
username navindars password hKEmegKvbMayue/0 encrypted privilege 15
username navindars attributes
vpn-group-policy SSLVPN
username LCCVPN password KKr3nUkVs/K4GsoE encrypted
username LCCVPN attributes
vpn-group-policy SSLVPN
service-type remote-access
tunnel-group VPN-SSL type remote-access
tunnel-group VPN-SSL general-attributes
address-pool VPNPool
default-group-policy SSLVPN
tunnel-group Client-VPN type remote-access
<--- More --->
tunnel-group Client-VPN general-attributes
address-pool VPNPool
default-group-policy VPN-Client
tunnel-group Client-VPN ipsec-attributes
pre-shared-key *****
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
<--- More --->
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:c6f5f803a4a33a27bf2ddc912aa8966a
: end
Solved! Go to Solution.
11-24-2020 02:46 AM
Dear All,
I hope you are fine.
I'm sorry to reply to this post because i have the same issue. I don't know if my config is complete or not. I tried to add NONAT, ACL,... rules to try to resolve the issue but it don't work.
please someone help me.
Thank you very much.
ciscoasa# sh run
ASA Version 8.2(5)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.0.1 IPSec-Gateway
name 192.168.0.0 RemoteIPSec-Pool
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.150.2 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address X.X.X.Y 255.255.255.248
!
ftp mode passive
access-list inside_nat0_outbound extended permit ip any 192.168.0.96 255.255.255.224
access-list Remote-Tunnel_splitTunnelAcl standard permit 192.168.150.0 255.255.255.0
access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.150.0 255.255.255.0
access-list RemoteIPsec standard permit RemoteIPSec-Pool 255.255.255.0
access-list 110 extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool testpool 192.168.0.10-192.168.0.15
ip local pool RemoteIPSec-Pool 192.168.0.100-192.168.0.120 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (inside) 1 interface
global (outside) 1 interface
global (outside) 2 192.168.20.10
nat (inside) 1 0.0.0.0 0.0.0.0
access-group 110 in interface outside
route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.150.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
.
.
.
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn1 1 set pfs group1
crypto dynamic-map dyn1 1 set transform-set FirstSet TRANS_ESP_3DES_SHA
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment terminal
crl configure
crypto ca trustpoint ASDM_TrustPoint1
enrollment self
subject-name CN=ciscoasa
crl configure
crypto ca certificate chain ASDM_TrustPoint0
...
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto isakmp policy 70
authentication pre-share
encryption aes-256
hash md5
group 5
lifetime 86400
crypto isakmp policy 90
authentication rsa-sig
encryption aes-256
hash md5
group 5
lifetime 86400
crypto isakmp policy 110
authentication pre-share
encryption aes
hash sha
group 5
lifetime 86400
crypto isakmp policy 130
authentication pre-share
encryption 3des
hash sha
group 1
lifetime 86400
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value local.domain
group-policy Remote-VPN internal
group-policy Remote-VPN attributes
dns-server value 192.168.150.200
vpn-filter value RemoteIPsec
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Remote-Tunnel_splitTunnelAcl
default-domain value local.domain
username testuser password IqY6lTColo8VIF24 encrypted
username testuser attributes
vpn-group-policy IPSec-GroupPolicy1
username test password P4ttSyrm33SV8TYp encrypted privilege 15
username arzoum password BLt4wvI5cO4pWEIY encrypted privilege 0
username arzoum attributes
vpn-group-policy Remote-VPN
tunnel-group DefaultRAGroup general-attributes
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
authentication ms-chap-v2
tunnel-group Remote-VPN type remote-access
tunnel-group Remote-VPN general-attributes
address-pool RemoteIPSec-Pool
default-group-policy Remote-VPN
tunnel-group Remote-VPN ipsec-attributes
pre-shared-key *****
11-24-2020 04:53 AM
This is the walkthrough, i followed : https://blogs.uw.edu/curreri/using-the-cisco-asa-5505-as-a-vpn-server-with-the-vpn-client-software/
Waiting your help please.
Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide