There are 2 methods of booting and running IOS XE software in 3850 switch/stack.
By default, the switches are shipped in Install mode.
Bundle mode: Bundle mode is where we boot the switch/stack using the .bin file. This is the traditional method of booting the switch where the switch extracts the .bin file to the RAM of the switch and run from there.
Install Mode: Install mode is where we pre-extract the .bin file in the flash and boot the witch/stack using the packages.conf file created during the extraction.
Install mode is the recommended mode of running the switch. Not all features may be available in this Bundle mode
IOS XE installation and software rollback are supported only when the switch is running in “Install” mode. (ie: The commands “software install” and “software rollback”.)
Use “software expand” command to convert the switch into Install mode from Bundle mode. The steps are mentioned below.
Upgrading a stand-alone switch:
The packages and provisioning file used to boot in installed mode must reside in the flash.
Booting in installed mode from usbflash0: or TFTP is not supported.
Booting a bundle in bundle mode is just like booting a monolithic IOS image.
For example: boot flash:cat3k_caa-universalk9.SSA.03.08.83.EMD.150-8.83.EMD.bin
Hence, the boot variable should not be pointing to the .bin file. If so, the switch will boot in Bundle mode. The boot variable should be pointing to the “packages.conf” file in order for the switch to boot in Install mode.
Before doing the upgrade, we need to check the mode in which the switch is currently booted in.
In order to upgrade the switch from Install mode, please follow the below-mentioned procedure.
•1. Download the new image from the TFTP server to the flash / USB on the switch. (optional)
Copy tftp: flash:
Copy tftp: usbflash0:
•2. Use the command “software install” to install the newly downloaded image (or) the image present in the network.
C3850-01#software install file <source>:<filename.bin> new
The “new” keyword is used so that that the post-install package set should contain only the packages being installed. The old packages file will be renamed for future rollback purpose. Without this option, the post-install package set is a merged set of the currently installed software and the new packages being installed.
The source can be
flash: or usbflash0: (or a sub-directory of these)
The network via tftp, ftp or http
NOTE: When performing ‘software install’ on a switch with a source bundle that resides in the network, the source bundle is first downloaded to RAM on switch. The source bundle is deleted from RAM when the operation completes.
Refer to the configuration guide to know about the other optional parameters of this command,
Directory of flash:/
29511 -rwx 220716072 Oct 15 2012 12:57:59 +00:00 cat3k_caa-universalk9.SSA.03.08.88.EMP.150-8.88.EMP.bin
[1 ]: Finished installing software. New software will load on reboot.
[1 ]: Committing provisioning file
[1 ]: Do you want to proceed with reload? [yes/no]: n
Once the installation is completed, reload the switch and it will boot into the newly installed IOS XE image.
From Bundle mode:
If the switch is currently running in “Bundle” mode, then we need to use the “software expand” command to convert the switch into the Install mode first and then install the new IOS XE.
The ‘software expand’ exec command is used to extract the package files and the provisioning file (packages.conf) from a source bundle (possibly the running bundle) and copy them to the specified destination directory in a local storage device.
This command will typically be used to convert from the bundle running mode to the installed running mode.
NOTE: When performing ‘software expand’ on a switch with a source bundle that resides in local storage, the source bundle is first copied to the corresponding local storage device on the switch. The source bundle used for the expand operation is left intact after it is expanded.
NOTE: When performing ‘software expand’ on a switch with a source bundle that resides in the network, the source bundle is first downloaded to RAM of the switch. The source bundle is deleted from RAM on the switch when the operation completes.
This example uses the following steps to prepare a switch for booting in installed mode, i.e., booting a package provisioning file (packages.conf)
Boot in bundle mode using ‘boot flash:<bundle name>’
Can also boot from usbflash0: or via tftp
Use the ‘software clean file flash:’ command to remove any unused package, bundle and provisioning files from flash:
Use the ‘software expand running to flash:’ command to expand the running bundle to flash:
Reload the switch
Boot the installed packages using ‘boot flash:packages.conf’
The 'software rollback' exec command can be used to revert to a previous version of the installed software package set (i.e., an older packages.conf file)
This functionality relies on the existence of one or more 'rollback provisioning files’ in flash:, along with all of the .pkg files listed in the rollback provisioning file(s)
The rollback provisioning files are visible in flash: as packages.conf.00-, packages.conf.01-, etc.
packages.conf.00- is a snapshot of the packages.conf file as it looked prior to the last installation operation
packages.conf.01- is a snapshot of the packages.conf file as it looked two installations ago
And so on
When the 'software rollback' command is used, packages.conf.00- becomes packages.conf. packages.conf.01- becomes packages.conf.00-. And so on
Note: If the 'software clean' command is used, future attempts to do a software rollback are likely to fail
Hello Experts, I could able to see many route-map when I give command sh route-map in CLI, but when I tried to see the running config I could able to see only 2 route-map that are bind to the BGP neighbor. Is there any command to check whe...
I am going to stack one C3850-12-S-S & two * C3850-24T-S so I am going to use it as LAN core and Please let me know about licence that I have to buy to run IP base IOS on 3850 and also please let me know any other licence I have to order ---
Dear all, I'm struggling with getting my Cisco ISR 1921 to do proper NAT. Setup:Laptop > Cisco ISR 1921 int Gi0/0 > Dialer1 > EHWIC-3G-HSPA+7 (Cellular0/0/0) I’m using NVI to do NAT. I can ping 220.127.116.11 both from router and fro...
Hi All ,n7k1 ---VPC --- n7k2 ..both have 6.2(2a) image ..if I reload n7k1 with the new image is 6.2(20) and once n7k1 comes online, will three be any breakage of VPN peer-link due to mismatch of OS versions of n7k1 and n7k2? After 20 minutes ,reload of n7...