The Supervisor Engines available for the Cisco Catalyst 4000 and 4500 Series Switches are positioned as such:
Supervisor Engine I Deployed in the Cisco Catalyst 4003 Switch only
Supervisor Engine II Deployed in the Cisco Catalyst 4006, 4503, or 4506 Switches for entry-level, and only Layer 2 switching with support for Cisco CatOS. For new opportunities, position the new Supervisor Engine II-Plus whenever possible.
Note: Supervisor I and Supervisor II only supports CatOS system software. In order to have Layer 3 functionality in these switches, you can install Catalyst 4000 Layer 3 Services Module (WS-X4232-L3).
Supervisor Engine II-Plus Deployed in the Cisco Catalyst 4006, 4503, 4506, or 4507R Switches for entry-level, Layer 2 switching with basic Layer 3 services. Optimized for small and medium-sized enterprises and education customers.
Note: Supervisor II-Plus (Sup2+). Sup-III, Sup-IV and Sup-V only support Cisco IOS system software.
Supervisor Engine III Supervisor Engine II-Plus delivers non-blocking Layer 2 switching with Layer 3/4 intelligent services to power resilient, multilayer switching solutions for converged data, voice, and video networks.
Supervisor Engine IV Deployed in the Cisco Catalyst 4006, 4503, 4506, or 4507R Switches for highly scalable Layer 2, 3, and 4 switching with advanced Layer 3 and 4 services for deployment flexibility and investment protection.
For all new opportunities, position the Supervisor Engine IV whenever possible. It delivers everything that the Supervisor Engine III offers plus redundancy, a NetFlow Services Card option, and dynamic buffer limiting, at a better price point.
Supervisor Engine VAn extension of the Supervisor Engine IV that offers higher capacity, nonblocking Cisco Layer 2-4 switching at 96 Gbps, with performance of 72 Mpps
Supervisor Engine V-10GE The Cisco Catalyst 4500 Series Supervisor Engine V-10GE offers non-blocking, Layer 2 4 switching with wire-speed 10-Gigabit Ethernet uplinks, that increases the Catalyst 4500 Series overall performance to 136-Gbps capacity and 102-mpps throughput.
When you run CatOS, then you see the (enable) prompt, and in Cisco IOS , you see > and # prompt.
You can check the operating system whether it is Cisco IOS or CatOS if you use the show version command output or if you check the type of Supervisor card.
These are the supervisor cards that support CatOS:
These are the supervisor cards that support Cisco IOS:
In Cisco IOS, you do not have to configure the sc0 interface because it does not exist, hence you need to configure the interface VLAN.
Hi all.Is it posible to deploy sdwan controller with two transport vpn / vpn 0 ? Is there any documentation about this? I cannot find any in sdwan controller, only in sdwan vedge with two vpn 0.Thank you. Best regards,Lazuardi Nurfaiz
Hai experts!In my work, i have experience to config connecting branches offices to data center edge router via BGP (with Metro E and MPLS media). But i curious about how to connect dc edge router to branch router vice versa via internet. Any idea? Do i ha...
HiI am trying to attach a feature template to n an C1111-8PLTEEAWE running 16.12.03 IOS-XE SDWAN. Controllers are running version 19.2.2. I manually configured the cisco router and it has sucessfully built control connections to the controllers. Now, I wa...
HiI have 3 type of catalyst : C3560G , C3750G and C2960All those switch are 48V DC switches and they work fine in the 48v energy environnement(see image below).I wants to install those 48v DC switches in an environment where there is only 220v...
Hello for everybody. I have the task - to configure logging on the 9300 switch and send logs to the log server. The logs should contain the following information: who performed actions on this switch and with which account. If i understood corre...