Only one WIC-1ENET card is supported in all versions of Cisco IOS Software Release 12.1, and 12.2 versions earlier than 12.2(2)XJ, 12.2(2)XK and 12.2(8)T. To work, the WIC-1ENET card must be installed in slot0. An error message is displayed when the router is running on one of the earlier Cisco IOS Software Release versions. In this case, the WIC-1ENET card will not function.
To resolve this issue, perform these steps:
Verify that the Cisco IOS Software Release version on the router supports the WAN Interface Card (WIC) being installed in slots other than slot0. Issue the show version command.
This is the output of the show version command:
1750#show version Cisco Internetwork Operating System Software IOS (tm) C1700 Software (C1700-SY756I-M), Version 12.1(3)XT1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) TACHomeSWIOSSpecials for info Copyright (c) 1986-2000 by Cisco Systems, Inc. Compiled Tue 12-Dec-00 2240 by detang Image text-base 0x800080E0, data-base 0x80AA27C8 ROM System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1) ROM C1700 Software (C1700-SY756I-M), Version 12.1(3)XT1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) WSFP-SEA uptime is 9 hours, 27 minutes System returned to ROM by reload System image file is "Flashc1700-sy756i-mz.121-3.XT1.bin" Cisco 1750 (MPC860) processor (revision 0x501) with 24576K/8192K bytes of memory. Processor board ID JAD04180C4U (3871931809), with hardware revision 0000 M860 processor part number 0, mask 32 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 1 Serial network interface(s) WIC with 56k 4-wire CSU/DSU 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System Flash (Read/Write)
In this example, the Cisco IOS Software Release version is 12.1(3)XT1. Therefore, the router supports only one WIC-1ENET card, and it must be installed in slot0.
Upgrade the Cisco IOS Software to a version that supports the router having the WIC-1ENET card in other slots and allows the use of two WIC-1ENET cards. This functionality is available in Cisco IOS Software Release versions 12.2(2)XJ, 12.2(2)XK, 12.2(8)T and later.
Hello everyone,,,How can i check ALL configuration implemented in the switches? "show archive config differences " didnt see much. Can i view the config in ID 1,2,3,4,5 below? KL04SW#show configuration history1 00:20:50 UTC Tue Sep 24 20192...
Hello,We have Nexus 9000 switches connected to ASA FWs, while I'm checking the log I've found the below;%ETHPORT-5-SPEED: Interface Ethernet1/1, operational speed changed to 1 Gbps%ETHPORT-5-IF_DUPLEX: Interface Ethernet1/1, operational duplex mode change...
HI Everyone, Thesedays, we are occuring a issue that is "show inv" command cannot display full info of two cat6500 device in VSS mode.We have done some steps on VSS before,First, we power down all cat6500 device(chassis1 is the active role,and ...
Dear All, We have a Catalyst 9200-24T-E stack and have hit the bug CSCvn30950, so we want to upgrade the IOS form 16.10.1 to 16.12.1 version. request to provide me the process to upgrade the IOS in stack from C9200 series without brea...