If you have any features/improvement suggestions, let us know below.
Forum Posts
Hello,background:I own a small company which has its own email, LADP, File and Web servers, I recently overkilled by purchasing a Cisco Nexus C9396TX and due the lack of graphic interface I did order at insight.com a license for the Cisco Nexus Dash...
Hello,We have recentry bought a NEXUS C9396TX and I been trying to configute the Management interphase to deploy the switch UI.I have configured the management interphase IP example: 10.10.10.3/27 gateway 10.10.10.2ping to 10.10.10.3 is alive but no ...
My customer has a NXOS VXLAN fabric and wants to enable PBR with L2 as the classification.. is this supported? The customer is using ND 3.2 with NDFC The fabric is full of L2 and the GW is in the external network.. on a L2VNI can we enable PBR where...
Hi experts, I am trying to deploy an NDI in a vND installed on a hyperflex cluster and seems that I fail miserably. The problem is that I cannot enable the NDI service. This is the setup: vND: 2.2.2dNDI: 6.1.3.943x Data Nodes: with recommended resour...
Hi expert, ND v3.2.1l + nxosv9k-9300v-10.3.1.F throws below error while recalulating, while the same Nexus firmware works perfect with NDFC v12.1.2e. Can anyone could share lights?
Hello Everyone,I'm trying to enable NDI service in my nexus dashboard vm for demo and learning purpose but i'm getting following erors. Can some help me pls.
In a nexus 9k vxlan evpn frabric with Tenant Routed Multicastis it possible to have multicast sources/receiver belonging to a vni for which default gateway is a couple of firewall (active/standby redundancy) ?I've read trm doesn't support svi for pim...
Resolved! Nexus Dashboard upgrade
I have to do a new deployment of Cisco Nexus Dashboard.The nodes have installed the 2.3 release that does not support the direct upgrade to version 3.2Is it better to do an upgrade to 3.0.1 versions and then 3.2 or do a direct reimaging to version 3....
Hi Guys,We have a cluster of Physical ND and we have set up 5.2.4d ACI Simulation and configured with few tenants replicating our Prod environment.We are trying to add ACI Sim fabric to Nexus Dashboard but its not getting discovered. From ND Cli, I c...
Hi team, When i try to add Cisco Catalyst 8000v to NDFC i get fault "Session Error (Code:103)". What's the cause? Could you ask me?
I have a lab NDFC. There was a landscape deployed. The switches have since been removed. NDFC is not removing the switch as there was a pending change. Cannot seem to backup of any changes as i cannot recalc a non-existing switch. Is there an opti...
Hello, I'm trying to delete a Fabric from NDFC which was previously monitored with Nexus Insight, and I'm getting the error: "Fabric xxx is registered with ND cluster(s):xx" But now the Nexus Insight cluster no longer exists (It was a PoC and the vms...
Resolved! NDFC data interface connectivity option
If NDFC is configured for out-of-band Management over ND management interface,is it possible connect ND data interface directly to a couple of leaf of the managed fabricjust for Endpoint Locator purpose, or Data interface adjacency is required to bri...
Come learn about Cisco's Nexus AI switches and Nexus Dashboard. It's around the corner, so register today! Generative AI demands cutting-edge networks to deliver low-latency, high-throughput performance. This session will explore building AI/ML fron...
Hey Team,This is a NDFC Multisite Setup where NDFC is a virtual cluster running latest version.I got existing Core Routers on each site,Core routers are in production providing L3 ServicesCore routers connect site-1 and site-2 as well and provide Lay...
