a 6506 flex-wan module with atm pa-a3 oc3 interface,the other side is a FORE hub7000.they connected each other through a pvc.6506 configuration is:int atm 4/0/0ip address 172.18.254.17 255.255.255.252pvc 0/200protocol ip 172.18.254.18 broadcast I tur...
Hi,I don't know whether the 15454E-ML100T-12= can support 12 point-to-point channels in the SDH environment? Could someone tell me?Thanks a lot!Sincerely
Hi, I don't know whether the following configuration can work well in the 15454e platform? Could someone give me a advisement? Thanks 15454E-E1-42= 115454E-E1-120NP= 115454E-E1-75BB= 115454E-E1-75-C-2 1...
Folks, I am fairly new to optical networking and working on a project. I would appreciate if someone could help me undersstand a few things.1)The customer has OC-12 in a dual ring setting. Does that mean that he is 622 Megs in both directions ...
I am currently running the following:Win 2000 ProIE 6.0Java 1.4.2_08-b03When I start the CTC initilization after the .jre files have downloaded I get the following error message: Error: Failure during IOR Repository InitilizationI have uninstalled al...
hello,Is it possible to connect a 10 Gigabit Ethernet LAN PHY client interface (12xxx or 76xx) on a 10 Gigabit Ethernet WAN PHY port of provider équipment (Nortel 5200) ?what about the existence of 10 Gigabit Ethernet WAN PHY interface on 12xxx or 76...
According to the Cisco XENPAK doc, LX4 uses WWDM. I couldn't find a whole lot of reference on WWDM.My understanding is that with CWDM and DWDM, you need either a passive mux/demux or a OADM for wavelength aggregation. Does that apply to WWDM as well?...
I am proposing an ONS 15530 with 8-port Muxponder card (15530-MSMP-0112)I need to connect to a Layer switch with GE using Single Mode Fiber.Referring to product data sheet athttp://www.cisco.com/en/US/products/hw/optical/ps2011/products_data_sheet090...
running 4.6.2 with the following ethernet modules - g1K-4, E1000-2G and E100-12TG modules.I'd like to splice an OC-12 circuit in the following manner:STS-6C port-mapped to G1K-4 module. (easy can do)STS-4 mapped to E1000-2G in single-card etherswitch...
We have had some very strange issues when creating Ethernet circuits in our ONS-15454. We are running software version 4.6.2. We have the E100T-G cards installed in 6 of our 20 nodes and they are provisioned as Port-Mapped. We also have one ONS-153...
Where could I find info about fiber optic cabling? I have mostly dealt w/ copper but now I would like to learn alot about fiber optic cabling, connecters, protocols...terms like SX, LX,and ZX .....Can someone steer me in the right direction...Thanks ...
We an ONS 15530 with a 15530-FCGE-8P card on slot 7. Physical ports are configured as follows: Ports 0 and 1 = GE, Ports 2 and 3 = GE, Ports 4 and 5 = ISC Compatibility, Ports 6 and 7 = ISC compatibility mode. Ports 5 and 7 are up. However, port 4 an...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: