Hi All, I have an older 7600 router that I would like to use to host NAT: I have the following config: ip nat inside source list 45 interface te5/5 overload ip dhcp pool NATnetwork 192.168.1.0 255.255.255.0default-router 192.168.1.1domain-name ‘test-...
Forum Posts
Hi Guys, We have 2 data centres and 2x Nexus 7K and 2x Nexus 5K per data centre. I want to implement fabricpath between Nexus 7Ks and Nexus 5Ks.Can I implement fabricpath like connecting all 4 nexus 5K edges to all 4 nexus 7K spines or connect 2x nex...
Resolved! 10 SFP Port, 2 SFP and 2 RJ45 Port
Hi,Please suggest switch for fiber communication like ( 10 SFP (fiber communication )port, and 2 SFP and 2 RJ45 port.
Resolved! SFP Receive Power Range
Hello Hope everything is working fine with you. Could you please do me a favor on below questions? We shut down the local SFP, and monitor the received power on opposite SFP. The received power is always -40dBM when we using below modules. I think ...
Hi - I have an ASR903 that is using two QSFP_40GE_SR4 optics (both are recognized in the ASR903 on the appropriate ports) but the optics are not linking together when I connect them. I am using an MTP to MTP Female connector. I will upload an image o...
Hi, I have a newly deployed DWDM on NCS2000, we have some out of span links, APC is taking care of that but i need to modify the parameters without changing the hardware setup. I need to lock the hardware specs in order modify the fiber dialog losse...
We see this issue quite often, we're staging an MSTP deployment of an NCS2006 M6 with dual TNC-Es, and we constantly lose connection to the shelf in CTC, making it difficult to setup some initial configuration parameters. This issue occurs on multipl...
Resolved! SFP Power Budget Calculation
Hi All, I'm new on designing the Fiber Optic link loss budget. Please help me understand very well about this calculation. I confused on some calculation:-1. How to know the SFP/SFP+ power budget? As per I google, (min Tx - min Rx) = Power Budget. 2...
Resolved! Gigabit to 10 Gigabit Upgrade
Hello there!My network backbone currently consists of 1000BASE-SX links using OM2 multimode G50/125 µm fiber. The lengths are approximately 108 m / 98 m / 43 m / 40 m.Now I'm supposed to upgrade to 10 Gigabit; what options do I have?10GBASE-SR offici...
Hi,I am using SG350-10P-K9-EU switch as part of my Home network.The switch is connected directly to a fiber optic cable via SFP module.The switch than connected via rj45 cat7 to tp link archer ac3150 in order to distrbutewifi to the rest of home to p...
Hello all, I have 2 Cisco 4506 with Sup 7-E cards and I want to connect them with the 10 Gig fiber ports. I have the 2 10 Gig SFP's in them and configured the interfaces on both sides as just trunk ports interface TenGigabitEthernet1/1 switchport m...
I have 4 GLC-ZX-SMD SFP's between two Cisco IE4000's, everything came up fine but ovenright I lost light and link. On one side I can still see -8.9db, but it's -40 on the other. My span loss OTDR'd out at 9db of loss not including my fiber patch ca...
HiI have a strange problem I have not come across before, where one end of a fibre connection shows as "connected" but the other end shows as "not connected".I have a C2960-48PST-L connected to a C3750X-12S-E via OM4 fibre. Both switches use GLC-SX-M...
Resolved! ASR920
Hi,I ask for your help in solving the problem.I have ASR-920-12SZ-IM without licenses for 10G interfases.The manual says: Without License: The licensed ports Te0/0/12 - Te0/0/15 operate in 1G mode.But when I install the optical 10G SFP in the Te0/0...
Hi, We recently bought an SG350X-48 switch.I would like to know if I can use an Intel E10GSFPSR Ethernet SFP+ SR Optics in port xg3 and xg4 for uplink to my server. sincerelyArnaud
