Hi,Recently changed analog media gateway from H323 to MGCP now our branch CME using h323 to CM Cluster, cannot send faxes, to the devices off the CM MGCP GW. Faxing does work the other way. How do i resolve this?Thank You
Hi,Recently changed analog media gateway from H323 to MGCP now our branch CME using h323 to CM Cluster, cannot send faxes, to the devices off the CM MGCP GW. Faxing does work the other way. How do i resolve this?Thank You
I actually have a users group under the CCM "users search base" path. And CCM can't see the user in this group. Is't normal ?I'm running CCM 4.1.3sr1, directory plug'in and AD 2003.Thanks for your helpcompany.lan|-ToIp-|| |-Users-|| | ...
Hello All,It is my understanding that PA does not support G.729. I have a PA server sitting at my central sites, and all my remote sites are using G.729 to reach phones in my central site. However, all of the remote site regions are configured to u...
HiI've been reading up on Mobility Manager and don't have it yet to test it but got some questions. I am not sure why you would want to setup a speeddial to MM. According to the doc, IP Phone should not be used as remote devise and I thought you use ...
Hi, I need to configure CDR, but i installed it some months ago, i don´t remember the username and password for accesing to CDR. Do you know how i can recovery it ?Regards. Luis.
I was wondering if anyone has every loaded the phone loads for CCME on a separate TFTP server rather than the router's flash? I do not know if it is possible or not. Any help is greatly appreciated.
Hello,I currently have a Cisco 3825 with IOS 12.4(1)b thus implementing CME 3.3.Running the 'show ephone phone-loads' I've detected the following regarding my 7940-7960 IP Phones:hostname#sh ephone phone-load DeviceName CurrentPhoneload ...
Anybody is aware of any source for ccm trace interpretation?
Hello,I have a 1721 router with no WIC interface yet.I would like to have IPPHONES on the LAN but only one connection to the POTS.If I buy:1 WIC-ADSL for Internet access and1 WIC for Pots connexion.Will it be sufficient?And which WIC should I buy for...
Does a reboot of the phone, disrupt the Ethernet connection?I'm performing an upgrade to CallManager from 4.1(2) to 4.2.(3) and the possibility of a reboot to the phones exists. Our accounting department nmight be working on month end issues. Their...
Folks, We have an H.323 gateway to out callmanager and have meetingplace. We can not dial meeting id from outside, even though dtmf-relay is enabled on all voip dialpeers, any ideas?Thanks
Has anyone had any issues with CCM 3.3.3(sr4) upgrade to 4.1.2? I have 160 station cluster to do. At the same time there is also an IPCC 3.5 ->4.x for that cluster.......thanks
I am looking for some info on doing this (admin guide)Some specific questions;1) will the integration wizard add all the users.2) how do I take all those users and subscribe them to ext mobilityThanks
How do I get around this problem? The voice interface and controller are shut down, I've rebooted, etc.MIA-2811(config)#controller t1 0/2/0MIA-2811(config-controller)#pri-grMIA-2811(config-controller)#pri-group timeMIA-2811(config-controller)#pri-gr...
Hi,I cant find a document on CCO that says how many conferences the below config supports. It says max sessions 6.Does that mean 6 x 8 party conference?As the PVDM2 with later IOS support 8 party conferences.Or does the above mean 6 parties total?I w...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-27-2024 02:35 PM | ||
09-24-2024 07:17 AM | ||
09-24-2024 06:32 AM | ||
09-24-2024 05:35 AM | ||
09-19-2024 05:56 AM |
User | Count |
---|---|
1 | |
1 | |
1 | |
1 | |
1 |