05-13-2013 07:38 AM - edited 03-15-2019 05:26 AM
I am trying
to install DMM-5.3.0.244.isov in the UCS B-series server | |
i am getting the below error |
Could anyone help.
Please give me the alias for DMM.
Solved! Go to Solution.
05-13-2013 07:49 AM
Which C series?
05-13-2013 08:02 AM
So I do have the same iso image you are trying to use. I think you may have an incorrect hardware configuration on your C210. Is it an off the shelf C210 or was it purchased as a DMM? I'm pretty sure DMM is only supported on a C210 that has hardware specd specifically for the DMM. Basically it is an appliance.
Cisco Digital Media Manager 5.3.x on UCS C210 (DMM-SVR-C210-K9)
I don't think I can't help you from here. You will have to contact TAC.
05-13-2013 07:42 AM
DMM is not supported on the B series.
05-13-2013 07:46 AM
Hi Mike,
I have also tried with the c-series server, am getting the same error.
Please help.
Can you give alias for DMM.
05-13-2013 07:47 AM
This document describes how to set up and administer the following Cisco Digital Media System (DMS) 5.2.x appliances:
•Cisco Show and Share appliances:
–Cisco Show and Share 5.3.x on MCS 7835-H3
–Cisco Show and Share 5.3.x on WAVE-574
–Cisco Show and Share 5.3.x on UCS C210 (SNS-SVR-C210EN-K9)
–Cisco Show and Share 5.3.x and Cisco Show and Share Reports 5.2.2 on UCS C200 (SNS-SVR-C200WG-K9)
•Cisco Digital Media Manager appliances:
–Cisco Digital Media Manager 5.3.x on MCS 7835-H3
–Cisco Digital Media Manager 5.3.x on UCS C210 (DMM-SVR-C210-K9)
05-13-2013 07:49 AM
Which C series?
05-13-2013 07:51 AM
C210 series i have installed but getitng error
Thanks a lot.
05-13-2013 07:56 AM
WHere did you get the iso you are using? I'm not familiar with that version. Is this a fresh install or an upgrade? Normally you have to upgrade from 5.2 to get to 5.3. You can't do a fresh 5.3 install unless you have a special iso that someone from Cisco posted to you.
05-13-2013 08:02 AM
So I do have the same iso image you are trying to use. I think you may have an incorrect hardware configuration on your C210. Is it an off the shelf C210 or was it purchased as a DMM? I'm pretty sure DMM is only supported on a C210 that has hardware specd specifically for the DMM. Basically it is an appliance.
Cisco Digital Media Manager 5.3.x on UCS C210 (DMM-SVR-C210-K9)
I don't think I can't help you from here. You will have to contact TAC.
05-13-2013 11:33 AM
i have 2 doubts still
1. i have only ucs server which is not purchased as dmm, can i try with DMM 5.4 VM image whether it will work.
2.
I need to implement Digital signage solution in my office workplace.
I have DMP 4400G and TV only , can I implement the solution without DMM,SNS,Stadium vision director.
Please suggest me your valuable inputs
Thanks a lot for your great support.
Rajesh
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: