Re: E1 Timeslots get stucked with S_R2_COLLECT R2_Q421_IDLE stat

asilveira · ‎11-19-2010

Hi all,

I am experiencing a problem with an E1 controller installed on a Cisco 2811 gateway. Since people make calls through the E1, some of the calls do not end correctly and the timeslots used by those calls get stucked with S_R2_COLLECT R2_Q421_IDLE status. From the gateway perspective those timeslots are unused and so free for new calls, but when it try to use them for new calls they are rejected. Does anyone know how could I solve this problem, please? Following are the controller configuration and the "show voice call summary" command output.

Thanks a lot!

!

controller E1 1/0/0
framing NO-CRC4
line-termination 75-ohm
ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani
cas-custom 0
country brazil
metering
debounce-time 20
seizure-ack-time 78
double-answer
category 2
answer-signal group-b 1

!

voice-port 1/0/0:0
translation-profile incoming CONVERTE-ANI-ENTRADA
echo-cancel coverage 32
cptone BR
timeouts interdigit 4

!

RCISPO01#sh voice call summary
PORT                     CODEC      VAD VTSP STATE                     VPM STATE
============== ========= === ==================== ======================
1/0/0:0.1       -          - -                     R2_Q421_IDLE
1/0/0:0.2       -          - -                     R2_Q421_IDLE
1/0/0:0.3       -          - -                     R2_Q421_IDLE
1/0/0:0.4       -          - -                     R2_Q421_IDLE
1/0/0:0.5       g711ulaw   n S_R2_COLLECT          R2_Q421_IDLE
1/0/0:0.6       -          - -                     R2_Q421_IDLE
1/0/0:0.7       -          - -                     R2_Q421_IDLE
1/0/0:0.8       -          - -                     R2_Q421_IDLE
1/0/0:0.9       g711ulaw   n S_R2_COLLECT          R2_Q421_IDLE
1/0/0:0.10      -          - -                     R2_Q421_IDLE
1/0/0:0.11      -          - -                     R2_Q421_IDLE
1/0/0:0.12      -          - -                     R2_Q421_IDLE
1/0/0:0.13      -          - -                     R2_Q421_IDLE
1/0/0:0.14      -          - -                     R2_Q421_IDLE
1/0/0:0.15      -          - -                     R2_Q421_IDLE
1/0/0:0.17      -          - -                     R2_Q421_IDLE
1/0/0:0.18      -          - -                     R2_Q421_IDLE
1/0/0:0.19      -          - -                     R2_Q421_IDLE
1/0/0:0.20      -          - -                     R2_Q421_IDLE
1/0/0:0.21      g711ulaw   n S_R2_COLLECT          R2_Q421_IDLE
1/0/0:0.22      -          - -                     R2_Q421_IDLE
1/0/0:0.23      g711ulaw   n S_R2_COLLECT          R2_Q421_IDLE
1/0/0:0.24      -          - -                     R2_Q421_IDLE
1/0/0:0.25      g711ulaw   n S_R2_COLLECT          R2_Q421_IDLE
1/0/0:0.26      -          - -                     R2_Q421_IDLE
1/0/0:0.27      -          - -                     R2_Q421_IDLE
1/0/0:0.28      -          - -                     R2_Q421_IDLE
1/0/0:0.29      g711ulaw   n S_R2_COLLECT          R2_Q421_IDLE
1/0/0:0.30      -          - -                     R2_Q421_IDLE
1/0/0:0.31      -          - -                     R2_Q421_IDLE

Felipe Garrido · ‎11-22-2010

What version of IOS is the gateway running? How quickly does one of the channels get stuck in that state?

Can you provide us with the entire running configuration as well as the output of the "show log" command?

-Felipe

asilveira · ‎11-22-2010

Hi Felipe,

Following is the partial show version output. I have checked the show log output, but there was no logs related to this problem.

Thanks!

Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(15)T8, RELEASE SOFTWARE (fc3)
System image file is "flash:c2800nm-adventerprisek9-mz.124-15.T8.bin"

Cisco 2811 (revision 53.51) with 243712K/18432K bytes of memory.

Processor board ID FTX1024A3NT
3 FastEthernet interfaces
3 Serial(sync/async) interfaces
1 Channelized E1/PRI port
1 Virtual Private Network (VPN) Module
2 Voice FXO interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)

Felipe Garrido · ‎11-23-2010

Can you also provide me with the "show run" output? If not the whole output, can you provide the dial-peer configuration?

-Felipe

spazziani · ‎03-16-2011

Hi Asilveira,

How did you resolve your problem with R2? . I am having the same problem. Follow the show version and settings of E1 controller.

Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Fri 03-Sep-10 05:39 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

bhpraetorium uptime is 2 weeks, 6 days, 16 hours, 18 minutes

System returned to ROM by reload at 23:21:13 GMT-3 Wed Feb 23 2011

System restarted at 23:22:28 GMT-3 Wed Feb 23 2011

System image file is "flash:c2800nm-spservicesk9-mz.124-24.T4.bin"

controller E1 0/0/0

framing NO-CRC4

ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 0

country brazil

metering

debounce-time 10

answer-signal group-b 1

dnis-digits min 1 max 4

voice-port 0/0/0:0

cptone BR

timeouts interdigit 3

timeouts call-disconnect 0

Status Voice Port

0/0/0:0.3 g711ulaw n S_R2_COLLECT R2_Q421_IDLE

0/0/0:0.5 g711ulaw n S_R2_COLLECT R2_Q421_IDLE

0/0/0:0.7 g711ulaw n S_R2_COLLECT R2_Q421_IDLE

Regards,

a398640924 · ‎04-14-2014

Hi Asilveira, Felipe and spazziani

How did you resolve your problem with R2? . I am having the same problem. With E1 controller in a gateway.

Thanks!

Jose

E1 Timeslots get stucked with S_R2_COLLECT R2_Q421_IDLE status