cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1114
Views
5
Helpful
8
Replies

Fax sending issues

Saravana JSR
Level 1
Level 1

We have user trying to send the fax message using right fax software, calls are hitting on CUBEs but fax not delivering to the recipient. Following are the numbers that we can check it in the logs as well

 

8048236956,
8048236936,
8044184916,
8048236957

 

logs shows this message : Try with the demoted called number 818048236956

we have collected the logs using

debug voice ccapi inout.

Kindly also let me know which debug command will give clear message for SIP calls.

Logs are attached herewith.

 

 

8 Replies 8

I can see Not Acceptable Media on the logs.

 

Have  you configured  below under voice service voip. if not try the below.

 

voice service voip
	fax protocol t38 fallback pass-through g711alaw or g711ulaw

 



Response Signature


kindly find our config...

voice service voip
ip address trusted list
----------
----------
rtp-port range 16384 32766
clid substitute name
clid network-provided
address-hiding
mode border-element license capacity 2000
media statistics
media bulk-stats
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
redundancy-group 1
no supplementary-service h450.2
no supplementary-service h450.3
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
supplementary-service media-renegotiate
redirect ip2ip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback
pass-through g711ulaw
no fax-relay sg3-to-g3
modem passthrough nse codec g711ulaw
h323
emptycapability
billing b-channel
no h225 timeout keepalive
h225 timeout ntf 500
h225 display-ie ccm-compatible
h225 connect-passthru
call preserve
sip
bind control source-interface GigabitEthernet0/0/0
bind media source-interface GigabitEthernet0/0/0
min-se 3600 session-expires 86400
session refresh
ds0-num
header-passing
error-passthru
registrar server expires max 600 min 60
no update-callerid
midcall-signaling passthru media-change
early-offer forced
sip-profiles 102
sip-profiles 150 inbound
no call service stop
!
!

Try this

fax protocol t38 fallback pass-through g711alaw or g711ulaw

 instead of  fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback



Response Signature


May I know the reason why this command setup previously, I want to reason and give an explanation for the necessary and need to convince the management that there is no issues of changing the command.

 

Current command : fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback -why it has done it as it is

 

Newly recommended as per your suggestion : fax protocol t38 fallback pass-through g711alaw or g711ulaw

We have captured the pcapng graph analysis and logs again. kindly check these and let us know if we change the previous command it will resolve an issues.

Please note that it is not working for some specific number not all the number.

 

These are the numbers which are not working

8048236956,8048236936,8044184916,8048236957

From the image you shared Working call is on t.38 and failed call is on g711.

 



Response Signature


Seems we have configured the given commands
kindly find the below and please let us know how we can see the medias not
accepted in the logs

voice service voip
ip address trusted list
----------
----------
rtp-port range 16384 32766
clid substitute name
clid network-provided
address-hiding
mode border-element license capacity 2000
media statistics
media bulk-stats
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
redundancy-group 1
no supplementary-service h450.2
no supplementary-service h450.3
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
supplementary-service media-renegotiate
redirect ip2ip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback
pass-through g711ulaw
no fax-relay sg3-to-g3
modem passthrough nse codec g711ulaw
h323
emptycapability
billing b-channel
no h225 timeout keepalive
h225 timeout ntf 500
h225 display-ie ccm-compatible
h225 connect-passthru
call preserve
sip
bind control source-interface GigabitEthernet0/0/0
bind media source-interface GigabitEthernet0/0/0
min-se 3600 session-expires 86400
session refresh
ds0-num
header-passing
error-passthru
registrar server expires max 600 min 60
no update-callerid
midcall-signaling passthru media-change
early-offer forced
sip-profiles 102
sip-profiles 150 inbound
no call service stop
!
!

 
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: