01-03-2005 09:39 PM - edited 03-13-2019 07:30 AM
To All,
I have an ISDN NM-HDV2-2T1/E1 card but it shows an orange LED 'AL' at the back of the 2821. Can anyone help?
yourname#sh run
Building configuration...
Current configuration : 2502 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname yourname
!
boot-start-marker
boot system flash c2800nm-entservicesk9-mz.123-11.T2.bin
boot-end-marker
!
card type e1 1 1
logging buffered 51200 warnings
!
username xxxx privilege 15 secret xxxxxx
no network-clock-participate slot 1
no aaa new-model
ip subnet-zero
!
!
ip cef
!
!
ip domain name yourdomain.com
no ftp-server write-enable
isdn switch-type primary-net5
!
voice-card 0
no dspfarm
!
voice-card 1
no dspfarm
!
!
!
!
!
!
!
!
!
!
!
!
ccm-manager mgcp
!
!
!
!
controller E1 1/0
linecode ami
pri-group timeslots 1-31 service mgcp
!
controller E1 1/1
pri-group timeslots 1-31 service mgcp
!
!
!
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address 172.20.1.221 255.255.255.0
duplex full
speed 100
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial1/0:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial1/1:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 172.20.1.51
!
!
ip http server
ip http authentication local
ip http secure-server
!
!
!
!
control-plane
!
!
!
voice-port 1/0:15
!
voice-port 1/1:15
!
mgcp
mgcp call-agent 172.20.1.32 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
!
mgcp profile default
!
!
!
!
banner login ^C
-----------------------------------------------------------------------
Cisco Router and Security Device Manager (SDM) is installed on this device. This
feature requires the one time use, initial credentials, of username "cisco"
with password "cisco".
Please change these publicly known initial credentials through SDM or IOS CLI.
Here's the Cisco IOS command:
no username cisco
NOTE: Please add a new username to be able to launch SDM for router management.
For more information about SDM please follow the instructions in the QUICK
START GUIDE for your router or at
-----------------------------------------------------------------------
^C
!
line con 0
login local
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
!
end
yourname#
Cheers,
L
01-04-2005 01:59 AM
Hi maybe it something with CRC, check with your operator.
/Pex
controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-31
01-04-2005 02:49 AM
Have you ordered DSPs (PVDM2) along with this module? NM-HDV2-XT1/E1 does not include any DSP by default.
01-04-2005 04:19 PM
Yes, I had put a PVDM-64 on the card.
I just don't understand why it didn't work.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide