cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1067
Views
0
Helpful
17
Replies

SIP and CME

Hi,

does anyone have a working configuration for CME and SIP phones? Please, just don't send me the document from CCO. This 2851 is driving me crazy, and I am at the end of my patience here.

Dragi

17 Replies 17

OK, I just got off the phone with Cisco. Adv IP Services is compatible with CME3.4 however you can't use SIP. SIP is only fully supported with IP Voice and IP Voice/Video IOS.

dweiner
Cisco Employee
Cisco Employee

Here's working SIP config using 12.4(4)T1 ip voice (c3845-ipvoice_ivs-mz.124-4.T1.bin). This was pasted into another router and came up fine. You obviously need to change IP addresses and phone mac addresses to match. Dial-peers are for trunking to my CCM 4.1.

! =======================================================

! Get MAC Addresses from phones and change below config

! under 'voice register pool x'. Make sure MACs are

! correct before pasting in config.

!

! =======================================================

! SET CLOCK FIRST!

! =======================================================

!

ip http server

ip http path flash:

!

!

username cisco1 password cisco

username cisco2 password cisco

username cisco3 password cisco

!

tftp-server flash:P003-07-4-00.sbn

tftp-server flash:P003-07-4-00.bin

tftp-server flash:P0S3-07-4-00.bin

tftp-server flash:P0S3-07-4-00.loads

tftp-server flash:P0S3-07-4-00.sb2

tftp-server flash:P0S3-06-3-00.bin

tftp-server flash:P0S3-06-3-00.sbn

tftp-server flash:P00307020200.loads

tftp-server flash:P00307020200.sb2

tftp-server flash:P00307020200.sbn

tftp-server flash:P00307020200.bin

!

!

sip-ua

!

voice register global

mode cme

!

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to sip

supplementary-service h450.12

sip

bind control source-interface GigabitEthernet0/0.21

bind media source-interface GigabitEthernet0/0.21

registrar server

!

!

voice register dn 1

number 47700

name SIP Phone 1

!

voice register dn 2

number 47701

name SIP Phone 2

!

voice register dn 3

number 47702

name SIP Phone 3

!

voice register template 1

exit

!

! Make sure of MAC addresses !!!!

!

voice register pool 1

id mac 000C.30D4.C55E

type 7960

number 1 dn 1

template 1

username cisco1 password cisco

codec g711ulaw

!

voice register pool 2

id mac 0030.94C3.8CFA

type 7960

number 1 dn 2

template 1

username cisco2 password cisco

codec g711ulaw

!

voice register pool 3

id mac 0030.94C2.65E8

type 7960

number 1 dn 3

template 1

username cisco3 password cisco

codec g711ulaw

!

!

voice register global

mode cme

source-address 10.1.21.254 port 5060

max-dn 10

max-pool 10

authenticate all

timezone 6

time-format 24

date-format D/M/Y

hold-alert

mwi stutter

mwi reg-e164

tftp-path flash:

load 7960-7940 P003-07-4-00

upgrade

load 7960-7940 P0S3-07-4-00

create profile

file text

!

!

telephony-service

load 7960-7940 P00307020200

max-ephones 10

max-dn 10

ip source-address 10.1.21.254 port 2000

timeouts interdigit 3

max-conferences 8 gain -6

transfer-system full-consult

transfer-pattern .

no create cnf-files

create cnf-files

!

!

!

dial-peer voice 1 voip

destination-pattern [2-6]....

session protocol sipv2

session target ipv4:10.1.11.1

preference 0

incoming called-number .

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 12 voip

destination-pattern [2-6]....

session protocol sipv2

session target ipv4:10.1.11.1

preference 1

incoming called-number .

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 8 voip

destination-pattern 8.T

session protocol sipv2

session target ipv4:110.1.11.1

preference 0

incoming called-number .

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 82 voip

destination-pattern 8.T

session protocol sipv2

session target ipv4:10.1.11.1

preference 1

incoming called-number .

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

end

!

!

hth,

Don

Don,

i thank you for the config.

Right on!

Dragi