Other Data Center Subjects

I am running into a problem were one of my VDCs (vdc 2) will not load on either of the dual sups I have in my chassis.  It looks to be stuck in a "Create Pending" state.  The only log that shows up that may be relevant is:7K01 %$ VDC-1 %$ %CMPPROXY-2...

Hello!   Recently i configured ERSPAN between Cisco Nexus 1000V and Cisco Catalyst 6513 (s72033-advipservicesk9_wan-mz.122-33.SXJ6.bin)   ERSPAN config on Cat6513: monitor session 10 type erspan-destination destination switch 1 intrusion-detection-...

I am looking for advice on CoLo Design, we have a pair of IE switches which (in a logical T-shape) connect the diverse ISP circuits on one side, on the other a colo edge switch block, and then south bound a hosted environment which is protected by a ...

Hi Everyone.i have two Nexus devices, last week i upgraded from NXOS 6.03 to 6.1(5a), but when the device had done, i saw the CMP module no response status in on SUP.Here is output in two devices. Everyone have any idea about it.---------------------...

Hi my friends:Do you konw where storage san device in dcnm because when i try to add another this show me that the same device exist,but i can found in screen, I attached the error message. Thank, Best regard.  Marco

2015 Mar 31 05:52:30 SZ_DC_SW_N5548UP_b %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet2/15 is down (Link failure)2015 Mar 31 05:52:32 SZ_DC_SW_N5548UP_b %ETHPORT-5-SPEED: Interface Ethernet2/15, operational speed changed to 1 Gbps2015 Mar 31 05:...

We have VPN connectivity through service provider network infrastructure. A remote site have firewall, router, switch and hosts.The problem we face is - I can ping them till the end from Data Center through VPN, but they can ping only from the firewa...

Hi I know the recommendation a couple of years back was only to connect servers to FEX ports. Is this still the case? Is anyone connecting devices other than servers to FEX ports? Is there any good reason I could not connect a router to my FEX 2232 T...

Hi,   I know VDC on nexus 7k can allocate interface ,fib acl tcam resources,  but how can vdc allocate memory and cpu resouces an sup2/sup2e and i/o module!   for example.   vdc  1 get at least 20% cpu , and he can reache beyond 20% cpu  if cpu ultil...

HelloI have two questions.I don't know what is different between Nexus 5696Q and 6004EFI think same chassis but not sharing module because of different module product IDsuch as N5696-M12Q and N6004-M12Q for 12ports 40G Another oneI saw nexus 6004x ch...

Dear All,Does  N2K-C2232PP-10GE  supports SFP Transceiver 1000BaseSX ? Ethernet111/1/1  Model:                 unavailable  Type (SFP capable):    unknown  Speed:                 1000,10000  Duplex:                full  Trunk encap. type:     802.1Q ...

I am new in my position and have never worked with Cisco before.  I need to change the admin passwords on a 5500 wireless controller and several 3750 switches.  Can some please give me the commands to do so once I Putty into the equipment.Thanks,Mich...

HelloCan you help me in understanding the architecture of ASR 1004 and ASR 1006. In my current network i am running ASR 1002 and planning for upgradation to ASR 1004 / 1006 with requirement of 5*10G port and 5*1G port. So which ASR model will be help...

Can i use this card (VWIC3-1MFT-T1/E1 ) as the wan interface facing the verizon t1 on a cisco 1921 router, internet only? typically we use HWIC CSU/DSU  as the wan interface card on Slot 0 SubSlot 0 with the below commands but the router wouldnt work...