Ask Me Anything Event Thank you for joining us for the Expert Insights Series on ACI & NDI: Empowering Data Center Excellence! Our Customer Success Specialists Cody Albea, Peter Nalley and Manuel Valasco will be available from May 15, 2025 through...
Hi allI have 2 FI's connected via FC port channel to Nexus 5k;s which connect via port channel to Netapp controllers.On the NetApp's I can see that the hba's of the blades are logged in on vtic (boot lun's - and yes blades are booted and active)while...
I have NX7010 chassis' with mixed M and F series line cards. Fucntions to implement include VDC, vPC, VRF, and L3 routing. What are the best practices for mixed chassis? I once saw a Cisco document talking about it but couldn't find it right now.Than...
Does the 7K support dual-homed FEX's with vPC+ and FabricPath?
Should default QoS for FCOE be automagically created when one enables feature fcoe ?I've just worked a problem where it did not, adding default FCOE QoS fixed the issue and allowed vfc's to come up...Only thing I can think of is that I had previously...
Hi. Is there any documentation on defined tasks of certain CoPP policies. While most are guessable then there are some that I have no clue about.For example class-map copp-s-selfIp ... if I had traffic matched by that policy exceeding the defined pps...
Hi All,Just wondering what does OTV run on? Directly over IP, of UDP or TCP. When I did google search, I see that OTV uses TCP/UDP ports 8472. But the OTV documents say it only adds 42 byte overhead. With 42 bytes, I could not account for TCP or UDP ...
HiI have a nexus 7010 with one M1 card and two F1 cards. I´m trying to set up packet capture for an IDS using VACL.It seems that ACL capture is not possible with F1 cards. Is this correct?Regards Björn
Hi there:I have a N7K that has a strange behaviour for meWhen I connect to console after the welcome message a command is executed In my case is 'terminal color':User Access VerificationN7K1 login: adminPassword:Cisco Nexus Operating System (NX-OS) S...
I have M1 48-port RJ-45 module and F2e 48-port SFP module in a 7K chassis. I like to have the ports from the two modules in the same OTV VDC (M1 ports for join interface and F2e ports for internal interface). Is NX-OS 6.2 the minimum to support M1 an...
Hi there,I have a Vmware Environment. The switch backbone is from Juniper. Can i configure Nexus 1000V on Vmware to communicate with Juniiper Switch. OR Nexus 1000v can be integrated with Cisco Switches only.Regards,Abhilash
Hello all,I have 6500 where all my datacenter vlans are aggregated. The 6500 switch has a L3 connection with my ASR 1002. I want to extend my vlan to remore location where there is another ASR 1002 and a 6500. Is this possible to do this using OTV b...
Hi Experts,Does OTV work over IPsec tunnels? We have a requirement to configure OTV over IPsec, OTV works fine over GRE tunnels without IPsec, when we apply the IPsec the OTV goes down...Anyone tried OTV over IPsec before? Any specific configuration ...
Hi,Can anyone please tell me what is the Heat dissipation of Cisco 3925, Cisco 2911 and Cisco UCS server.RegardsSaurabh
Hi,I'm thinking to get another 5108 chassis and new blade servers to the existing UCS environment, 6140XPs with 2.0(1a) firmware, B200 M1 blade servers and 2104 IOMs.I'm curious whether the new chassis and B230 blade servers will be compatible with m...
Good evening,after upgrading some 7K from 6.1 to 6.2.2 we encounter the following issueinterface go in xcvrInval state and nothing we do can change it unless changing to a fet or 1G spf.The same optic in a 6.1 chassi is seen correctly.xcvrInval is se...
