hello experts,Just I have a quesiton, and much apprecicate if you can provide the answer.my question is; what is IP Planning / Operation department in GSM or SP companies?thanks a lot in advance.
We have four 7Ks (two in Data Center 1 and two in Data Center 2) which are used to implement OTV in a multi-homed configuration. I've included a PDF which shows the L2 and L3 topology. When one of the links went down (as depicited in the 2-page dia...
HiRunning latest 6.0(2)N2(1) code on my 5548s. I would like to source all outgoing ssh sessions from the switch loopback0 interface.The cli has "ip telnet source-interface" but no "ip ssh source-interface"Is this a bug/oversight?Thanks.
i am testing the implementation of otv using the asr's not the 7k's, the code just came out to support it. The config is different on the asr compared to the 7k's and i can not find any doc's worth while on the asr's, i have read the white papers whi...
Folks,When running OTV in Unicast mode, is support for Multicast traffic enabled across the Overlay automatically?Is there any additional configuration required to support Multicast frames across the Overlay or are they forwarded just like Broadcast ...
Hi,I am looking for a switch platform for a small DC that can provide high density 10G and good L3 performance. I was thinking of Nexus 6001 as L3 performance is better thant 5548/5596 and it supports FabricPath. Than I have also looked at the 4500X ...
Hi: I am trying to download Fabric path related mibs esp below two. CISCO-FABRICPATH-TOPOLOGY-MIBCISCO-SWITCH-FABRIC-MIBI am getting this error "The Page You Have Requested Is Not Available http://tools.cisco.com/auto/mibs/v2/CISCO-FABRICPATH-TOP...
HiWe have an N7k out of a pair in a DC that has recently started giving us the above error message on ports.These ports are mostly in port channels that are using VPCs with the other 7K to span it across both switches.We started to notice the issue ...
Hi all,Can we make 2 different port-channel as vpc peer-link. Example:interface port-channel 10vpc peer-linkinterface port-channel 20vpc peer-linkIs this working as vpc peer-link
HiI'm in the process of designing a small DC implementation and would like to use 2248s for ToR sever connectivity. Due to the scale of the requirement a 7000 with VDCs etc would be overkill. Therefore I'm looking at deploying a collapsed core/distri...
What would the the step and concerns be when introducing the F2 series modules to my current chassis?Do I need the fabric 2 module installed first before the installing I/O module?After inserting the I/O module do the ports go to vdc 0 for allocation...
I am trying to figure out a best Nexus solution for my Network which comprise of HP Server Platforms. (HP-DL380p Gen8 E5 Proliant.We generally have VLANs within the LAN and MPLS in Metro Links and IPVPN on WAN Links.Being new in the Fabric world, Env...
Hi all,I´ve got a problem with a new line-card I´d like to install in our Nexus 7010.Informations around the N7k:Installed SW (system/kickstart) NXOS 6.1(1).3x 6kw power.Line-Card should be installed in Slot 8. There´s already a F-card (N7K-F248XP-25...
Hi,i have a problem with N5K keepalive link over mgmt 0the mgmt 0 port is connected to a N2K on a N7K.the port on N2K is access vlan. and is put to a Network Management VLAN.but i still cannot ping each other from the management port and the keepaliv...
Hi,We've got two Nexus 5548UPs that are vPC and HSRP peers.I've had some feedback that I should incorporate the tracking function to close the vPC down in the case of a layer 3 problem, the thing is I'm not sure it's required. I can see in this artic...
