Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
I am using 5548 and 5596.both are running 5.1(3)N1(1a)According to VPC domain documentation, you want to issue the peer-switch command to ensure that both switches in the VPC domain are STP rootthese switches do not have the peer-switch command avail...
Hello,We have a N1KV version 4.2(1)SV1(4) and I have been getting the following error message, which I can't seem to understand (no reference either in cisco or on the web).2012 May 22 15:16:49 MKBE1NX1 %DAEMON-3-SYSTEM_MSG: ERROR, mts_send failed, E...
HelloI have a doubt, I need to know if is necessary upgrade NX-OS, I have a Nexus 7010 with ios n7000-s1-dk9.4.2.4.bin, I don't have access to use bug toolkit,Someone can I tell me if is there a bug in IOS n7000-s1-dk9.4.2.4.bin?thanks
Does anyone know if a later version of NX-OS will be able to differentiate between "deny" vs "permit" in NX-OS QoS ACLs? The NX-OS QoS documentation states that the permit and deny keywords are ignored for the purposes of matching in QoS class-maps....
Hi,I am finding it very hard to understand the Qos architecture of Nexus 7k (and 5K). I know about MQC and all that stuff, but unable to fully understand the architecture of qos in Nexus. I am looking for a good document that explains how the packets...
I haven't been able bringing up links between N7k and and the new N5K (5548UP) due to errors with UDLD.Someone else facing same problem ?regardsEdmundN5K:Software BIOS: version 3.5.0 loader: version N/A kickstart: version 5.1(3)N2(1a) sy...
Hi all,while reading through Cisco Doc I noticed that ISSU is on the N5K possible only L2 ?! ->When a Layer 3 license is installed, the Cisco Nexus 5500 Platform does not support an ISSU. Hot swapping a Layer 3 module is not supported. Is there an ...
I have 2 7Ks and will run VPC and multiple VDCs.Should it be a separete VPC Peer-link and keep-alive link per VDC?I am not sure but I guess yes since a physical interface should be allocated to a VDC.I just need confirmation.thanks
Hi,We are using F5 Load balancer i want to see the error logs through CLI but our device showing "tmos" mode i want to check through normal mode.Otherwise tell me how to check erroe logs from "tmos" mode.a0225199@F539001(Active)(tmos)#a0225199@F53900...
Hello All,I have a clarification with respect to double sided VPC.Following are the details:-1) Nexus 7K - 2 numbers2) Nexus 5K - 4 numbers3) Nexus 2K - 8 numbersThe 2K will be connected to 5Ks and 5Ks to the 7Ks. We plan to use double sided VPC and ...
Hi.I am trying to look for Nexus 5K config when the nexus2K FEX is dual-homed into it.What will be the configuration on both 5K especiall the pinning?Assuming one N2K 10G port is connected to N5K-1 and another N2K 10G port connected to N5K-2?N5Ks are...
Hi.Can anyone share config for optimal double-sided VPC?It is noted in the documentaiton to keep the 5K switches' uplink ports to 7K on the same portchannel groups.
I'm trying to capture Fabricpath frames on Nexus 7k N7K-F132XP-15 line card. The SPAN session is working, but only capturing the payload of packets, not the Fabricpath header. Does anyone know if there is some sort of ASIC limitation on the card th...
