Hi everybody,Please hepl me resolve this case.We have DR distance from DC about 30km. In DC, we have 2 Cisco Nexus 7K devices.In DR, we have 2 Cisco Nexus 9K devices.Between DC and DR, We have 2 DWDM connections.Can you have a any solution to aggrega...
Forum Posts
So I have a VM on a server that is connected to a Sw1 and Sw2 that are configured for VPC so the server the VM is on is dual homed. I can ping the VM at 172.16.10.10 for couple minutes or so then I can't for couple minutes or so. The switches do all ...
Resolved! Cisco OTV
Hi Guys, I have to configure OTV between my DC's. On one side, I have only one VDC and I can configure 2 more VDC's. But on another end, I already have 3 VDC's configured. Can I still configure OTV between these 2 datacenters?
Hi Gentlemen, I want to suppress route that is redistributed into BGP through "redistribute static" command and thus want to minimize prefixes advertised from my router to remote ISP Can I do it through a prefix-list ? Please find my solution...
HiI hava a problem about UCS Blade re-acknowledging.I had the problem blade to decommission, and replace the same model blade.But when I insert the Blade, but it still show Needs ResoulationAnd I Click e-acknowledge , it show "failure reacknowledge S...
Hello everybody, I've a customer case with two DC's where we use OTV as DCI. Each DC has two N7K with four VDC's named Prod, FCoE,DMZ and PoC. We want to stretch the VLAN's from this four VDC's over OTV. But on the Cisco documentation, I can't find ...
Cisco Catalyst 6500 Series 16-Port 10 Gigabit Ethernet Module can I use WS-C4506-E switch
Hi All, The ucsmsdk python package provides a code-gen feature which automatically generates python code when we do some activity over UCS manager. I have tried it over a UCS emulator. But when i tried the same with the actual hardware, it failed...
Hello, Could someone help me determine if OTV is supported on the Nexus 3K line of switches, specifically the 31108TC-V? I do not see the 3K line in the Cisco featureset navigator. Thanks a lot for your help! *Update* Heard back from my Cisco rep OTV...
Hi We are trying to migrate N7000 (F2) to N7700 (F3). While copying configuration and reloading N77 we see following error ....Tcam will be over used, please enable bank chaining and/or turn off atomic update.If bank-chaining is enabled on other mo...
I am trying to install ESXi 6.5 on a C240M5L server but in the process of installation it does not detect the virtual disk, I have 6 hard drives in RAID 5
Hello Hans, Seeking for support from you, I've got a scenario where I need to choose breakout 40g-4x10g cable between Nexus 31108TC-V and Catalayst 3850Stack. I've some doubts regarding this. Below is topology detail Doubts 1. If I use breakout...
Hi Team, Need suggestion to migrate Data Center. We have a plan to move eg Heathrow Data Center to Swindon. There are many Services hosted in Heathrow like DHCP Services, Juniper Remote access VPN services. Apart from that, there are many applicati...
Hi Team, We have a plan to migrate one of our DC in Heathrow to Swindon. We do not have much information about application dependanies, so we are planning to keep IP addressing in Target DC for Servers, VMs. Could you please confirm if we can use C...
there is one SM Fibre of 20 Km distance and which I want to connect on N5K-C5548UP model of switch , can any suggest which model of SFP should I use to connect this Single mode Fibre to my N5K switch . IOS of N5K switch is version 6.0(2)N2(1).
