Ask Me Anything Event Thank you for joining us for the Expert Insights Series on ACI & NDI: Empowering Data Center Excellence! Our Customer Success Specialists Cody Albea, Peter Nalley and Manuel Valasco will be available from May 15, 2025 throug...
Forum Posts
Dear Support, Any body can help me in how to revert back the VSS in cisco 6500 in to stand alone switch , in case VSL link didn't come up during the migration in to VSS. Regards Muhsina
Hi All, Do we assign the same IP address to the management interface on a dual SUP Nexus 7706 chassis and assume only the active SUP will respond to arp and ssh requests ? Will it actually allow me ? As I don't want to assign two different IP address...
Hello I have Nexus 7010 switch. I can't find feature dhcp and cannot even put command ip helper address for dhcp relay on svi. Please can anyone guide me?
Hi, In Access layer (Double sided VPC topology ),Is there any issue in configuring mgmt ports as keep alive link . Thank you
This is in regards to a caveat re: Nexus 7018. The issue is incompatibility between the N7K-M148GT-11L and the N7K-F312FQ-25= card running in the same VDC. Can you tell me where this is found in the documentation?
Hi, Why do we need a layer 3 point to point link between two aggregation switch in addition to the vpc peer link and keep alive link. What is the pros and cons Thank you
alert information : %USBHSD-STANDBY-1-ABSE%AUTH-3:error:PAM authentication error for admin from rted to save debug logs
Hello All,I got error message when I my router first boot (3845). *** Bus Error (Load) Exception ***Access address = 0x835acaf7 PC = 0x8000c438, SP = 0x8000c408, RA = 0xbfd9de20 Cause Reg = 0x0000041c, Status Reg = 0x30408003Uncorrectable ECC from L2...
Hi, I have a Nexus 7010 with below result of show inventory command: NAME: "Chassis", DESCR: "Nexus7000 C7010 (10 Slot) Chassis "PID: N7K-C7010 , VID: V01 , SN: TBM13154390NAME: "Slot 1", DESCR: "10/100/1000 Mbps Ethernet Module"PID: N...
I was asked a question and when i started over thinking the answer, i got myself unsure so i hope someone can help. I have a GigabitEthernet with a fiber SFP (GLC-SX-MMD-CT) and had a question about BW. is the interface capable of 1gb up and 1gb d...
Hello everyone, I was using cisco 3945 router for WAN Connectivity and WAAS below is the BoQ C3945-VSEC-SRE/K9Cisco 3945 SRE Bundle, SRE 700, PVDM3-64, UC, SEC Lic. PAKCON-SU1-3945VSSRIPS SVC, AR NBD Cisco 3945 SRE BundlePWR-3900-ACCisco 3925/3945 AC...
Hi, I would like to know whether Cisco ACE 4710 will support NAT64 or not. If yes, could you please share the configuration Software Version: *********************system: Version A4(2.3) Regards, Siva Shankar S
Good morning all, I am getting started using a Nexus Data Broker (and Cisco in general), so please take it easy on me. I cannot figure out how to get the NDB to pass traffic. I believe that I have the Configured Ports, Monitoring Devices, Configur...
Resolved! N7K Ugrade Path 6.1(2) to 7.2(1)D1(1)
Hi I would like to upgrade my Nexus 7010s and want to check if an upgrade to an intermediate release is first required. I have 2 x N7Ks running 6.1(2) and want to upgrade to 7.2(1)D1(1). Each N7K consist of the following modules. Each has dual sup...
Resolved! Nexus 7000 Upgrade from 6.03
About to upgrade from 6.03 due to Bug and I am told that the upgrade form 6.03 has a Bug - anyone perform an upgrade from this code? Looking for lessons learned, caveats. etc. etc. Plan to go to 6.15a (min recommended release for 7010) and then to 6...
