cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1310
Views
0
Helpful
4
Replies

Cisco UCS Central High Availability (HA NOT READY)

Matthew Tandy
Level 1
Level 1

I am seeing the following message in UCS Central about HA NOT READY

 

Cluster Id: 0x819cae86c88f11e4-0x8fb4d5434d9b9e52

Start time: Tue Mar 24 12:08:20 2015
Last election time: Tue Mar 24 12:08:50 2015

A: UP, PRIMARY
B: UP, SUBORDINATE

A: memb state UP, lead state PRIMARY, mgmt services state: UP
B: memb state UP, lead state SUBORDINATE, mgmt services state: UP
   heartbeat state PRIMARY_OK

HA NOT READY
Waiting for response from device.
Device count, expected: 2, active: 0
Detailed state of the device selected for HA quorum data:
Device 1009, serial: 14713e4e-929e-11e3-aa5e-002a6a7fa904, state: inactive
Device 1008, serial: 7cafb282-b1ed-11e4-a520-8c604f230301, state: inactive

Quorum data local IO failure:
14713e4e-929e-11e3-aa5e-002a6a7fa904 READ_FAILED, error: GENERAL, error code: 32767, error count: 1348947
Quorum data local IO failure:
7cafb282-b1ed-11e4-a520-8c604f230301 READ_FAILED, error: GENERAL, error code: 32767, error count: 1348947
Warning: there are pending I/O errors on one or more devices, failover may not complete
4 Replies 4

Matthew Tandy
Level 1
Level 1

Also the only way for me to cluster force primary is to shutdown the pirmary node and wait for the secondary to notice the peer is down

The management services on each node are all running

show pmon state

SERVICE NAME                                 STATE     RETRY(MAX)    CORE
------------                                 -----     ----------    ----
pmon                                       running            N/A     N/A
core-svc_cor_dme                           running           0(4)      no
service-reg-svc_reg_dme                    running           0(4)      no
core-svc_cor_secAG                         running           0(4)      no
operation-mgr-svc_ops_imgMgmtAG            running           0(4)      no
resource-mgr-svc_rsrcMgr_dme               running           0(4)      no
identifier-mgr-svc_idm_dme                 running           0(4)      no
central-mgr-svc_centralMgr_dme             running           0(4)      no
service-reg-svc_sam_controller             running           0(4)      no
policy-mgr-svc_pol_dme                     running           0(4)      no
sam_cores_mon.sh                           running           0(4)      no
core-svc_cor_controllerAG                  running           0(4)      no
operation-mgr-svc_ops_dme                  running           0(4)      no
service-reg-svc_sam_licenseAG              running           0(4)      no
policy-mgr-svc_sam_pkiAG                   running           0(4)      no
core-httpd.sh                              running           0(4)      no
stats-mgr-svc_statsMgr_dme                 running           0(4)      no
core-svc_cor_sessionmgrAG                  running           0(4)      no

 

I can ping the two registered domains from both nodes

I have the same problem....

VPLUCEMADPE01-A# show cl
cli      clock    cluster
VPLUCEMADPE01-A# show cluster state
Cluster Id: 0x8b736a1e766611e5-0xa29e69b27d244196

A: UP, PRIMARY
B: UP, SUBORDINATE

HA NOT READY
No device connected to this VM

 

I can't connect to Web-Management to VIP

 

Thank you

what do you get if you do

show cluster extended-state