New installation (and I'm new on the N9500s).......Attempting to do some failover testing before going into production. When I commanded a "system switchover" from active SUP to backup SUP, switchover occurred, but what was the primary SUP now shows "powered-up" and never reloaded completely. Manual "reload mod 27" has no affect. Vers 7.0(3) I3. Redundancy status shows it is configured. Is there something I'm missing?
Please see below, and thanks!
NFC9975MDFFCSSW21A# show boot auto-copy
Auto-copy feature is enabled
NFC9975MDFFCSSW21A# show mod
Mod Ports Module-Type Model Status
--- ----- ------------------------------------- --------------------- ---------
1 52 48x1/10G-T 4x40G Ethernet Module N9K-X9464TX2 ok
2 52 48x1/10G SFP+ 4x40G Ethernet Module N9K-X9464PX ok
3 52 48x1/10G SFP+ 4x40G Ethernet Module N9K-X9464PX ok
22 0 Fabric Module N9K-C9508-FM ok
23 0 Fabric Module N9K-C9508-FM ok
24 0 Fabric Module N9K-C9508-FM ok
26 0 Fabric Module N9K-C9508-FM ok
27 0 Supervisor Module powered-up
28 0 Supervisor Module N9K-SUP-B active *
29 0 System Controller N9K-SC-A active
30 0 System Controller N9K-SC-A standby
Mod Sw Hw Slot
--- ---------------- ------ ----
1 7.0(3)I3(1) 1.1 LC1
2 7.0(3)I3(1) 1.3 LC2
3 7.0(3)I3(1) 1.3 LC3
22 7.0(3)I3(1) 2.4 FM2
23 7.0(3)I3(1) 2.5 FM3
24 7.0(3)I3(1) 2.4 FM4
26 7.0(3)I3(1) 2.4 FM6
28 7.0(3)I3(1) 1.0 SUP2
29 7.0(3)I3(1) 1.5 SC1
30 7.0(3)I3(1) 1.5 SC2
Mod MAC-Address(es) Serial-Num
--- -------------------------------------- ----------
1 00-a6-ca-5c-89-e4 to 00-a6-ca-5c-8a-27 SAL2033UJBB
2 84-3d-c6-b0-aa-94 to 84-3d-c6-b0-aa-d7 SAL2031TY6H
3 84-3d-c6-af-c3-54 to 84-3d-c6-af-c3-97 SAL2030TMBB
22 NA SAL2023RHP1
23 NA SAL2028T66Z
24 NA SAL2021QPXL
26 NA SAL2021QPWL
28 e0-0e-da-36-89-b0 to e0-0e-da-36-89-c1 SAL2029TEUE
29 NA SAL2031UA5Z
30 NA SAL2031U61L
Mod Online Diag Status
--- ------------------
1 Pass
2 Pass
3 Pass
22 Pass
23 Pass
24 Pass
26 Pass
28 Pass
29 Pass
30 Pass
* this terminal session
NFC9975MDFFCSSW21A# show redundancy status
Redundancy mode
---------------
administrative: HA
operational: None
This supervisor (sup-28)
-----------------------
Redundancy state: Active
Supervisor state: Active
Internal state: Active with HA standby
Other supervisor (sup-27)
------------------------
Redundancy state: Standby
Supervisor state: Unknown
Internal state: Other
System start time: Mon Jan 30 23:16:22 2017
System uptime: 19 days, 3 hours, 41 minutes, 22 seconds
Kernel uptime: 19 days, 3 hours, 54 minutes, 59 seconds
Active supervisor uptime: 2 days, 19 hours, 36 minutes, 17 seconds
NFC9975MDFFCSSW21A#
