cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
191
Views
0
Helpful
5
Replies
Beginner

VxLAN Multisite getting traffic out from only one site

Hello,

 

The question is the following i have 2 DC:

Site1 - Principal

Site2 - Secondary

 

The thing is my principal internet connection will be on Site1 and i have a network with multisite (192.168.120.0/24) and a server 1 on site 1 (.10) and a Server 2 on site 2(.20).

 

So the thing is that the server1 and server 2 need to get to the internet from Site 1 and only and in case of a faliure on site 1 the internet conection on site 2 should be use.

 

i all ready have ping from Server1 to Server2 and it works, so the question is.

Is this posible or not?

Saludos,

Gerardo Andree Mejia

Everyone's tags (1)
5 REPLIES 5

Re: VxLAN Multisite getting traffic out from only one site

Hi @vivarock12,

Based on your description, I would expect the Border Leaf Switch (Leaf Switch where local Firewall connects to) on each fabric (site) to advertise a BGP EVPN type 5 default route (0.0.0.0/0).

Based on regular BGP path attributes, each Leaf Switch (aka VTEP) would compare the 0.0.0.0/0 its local Border Leaf advertises vs the 0.0.0.0/0 received from the Border Gateway (BGW) Switch (Switch that interconnects with the other sites in Multisite configurations).

You Border Leaf and Border Gateway happen to be the same device based on your topology.

The winner on each site would be the local 0.0.0.0/0 based on just Local_Preference BGP path attribute.

This logic is based on the fact that iBGP EVPN sessions are configured within the site and eBGP EVPN session is used to advertise the IPs and MACs across different sites.

Perhaps you can try increasing the Local_Preference on the BGW on site 2 for the 0.0.0.0/0 route site 1 is advertising so it can be preferred over its local 0.0.0.0/0 route.

 

NOTE: I have not tested this myself.

 

Regards.

 

See

BGP Best Path Selection Algorithm

Beginner

Re: VxLAN Multisite getting traffic out from only one site

Hello,

 

Actually i have that done that before and the best path default route for the second site is al ready the default route of the first site but the thing is, trafic still doesnt go through the first site.

From the pc on the Second site i can ping the ip of the Border leaf that connects to the InterTenant firewall but when i try to ping the Firewall the reponse never comes.

 

Any idea why and is it posible to do this to use the primary site to get the trafic from site to to get out?

 

and thanks for the @Hector Gustavo Serrano Gutierrez .

 

Saludos,

Gerardo Mejia

Re: VxLAN Multisite getting traffic out from only one site

Hi @vivarock12,

I think this should work since this is just VXLAN routing between sites in VXLAN BGP EVPN Multisite environment.

If traffic generated from PC in Site 2 does not hit the Firewall located in Site 1, I would suggest to start with looking at the VRF routing table on Leaf Switches, Border Leaf Switches and Border Gateways to ensure that the default route is properly installed for that specific Tenant (VRF).

If routes are in place, a common mistake I've seen in the configuration of VXLAN BGP EVPN Multisite greenfield deployments is the use of sub-interfaces for the DCI links. You must ensure that a physical L3 interface is used to connect the DCI link on the Border Gateway (BGW).

I'd suggest also go thru the entire Configuration Guide document and ensure you have a complete and consisting configuration including L2VNIs, L3VNIs, SVIs, VRFs, RDs, RTs, etc.

 

Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 9.3(x)
Chapter: Configuring Multi-Site

 

Regards.

Beginner

Re: VxLAN Multisite getting traffic out from only one site

Hello @Hector Gustavo Serrano Gutierrez,

 

I just got the configuration running, the thing was that i forgot to put on the Route-Map of the reditribution of the bgp to the OSPF that conects to the ASA to put:

 

route-map RM-TRAFICO_VXLAN_LANs permit 10 
 match ip address prefix-list TRAFICO_VXLAN_LANs
 match route-type internal external

 

and that was it so just one extra question if you can help me with it.

 

Is this the best way to do the redundancy to the DC or is ther any recomendation?

 

Thanks for the help by the way again.

 

Saludos,

Gerardo Mejia.

Re: VxLAN Multisite getting traffic out from only one site

I am glad it is working OK now @vivarock12,

Just as a final comment, check properly your failure scenarios and preferably test tem so you can make sure that Routing will respond to failures as you expect.

Regards.

CreatePlease to create content
Content for Community-Ad
August's Community Spotlight Awards