Hello,
Do you know what is this about?
CTT row 3800 ... it seems the box doesn't accept any commands I try to provision under the dsl ports.
Here is what I have:
dslam02-test.40nr# sh ver
Cisco Internetwork Operating System Software
IOS (tm) NI2 Software (NI2-DSL-M), Version 12.2(12)DA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Wed 23-Apr-03 11:55 by torowe
Image text-base: 0x800082EC, data-base: 0x8173C000
ROM: System Bootstrap, Version 12.0(5)DA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
BOOTLDR: NI2 Software (NI2-DBOOT-M), Version 12.2(12)DA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
dslam02-test.40nr uptime is 12 minutes
System returned to ROM by power-on
System image file is "flash:ni2-dsl-mz.122-12.DA2.bin"
cisco 6160 (NI2) processor with 60416K/5120K bytes of memory.
RC64475 CPU at 100Mhz, Implementation 48, Rev 0.0
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
16 G.SHDSL DSL Port interface(s)
4 ATM network interface(s)
522232 bytes of non-volatile configuration memory.
4096K bytes of Boot Flash (Sector size 128K).
16384K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
dslam02-test.40nr#sh hard
dslam02-test.40nr#sh hardware
Chassis Type: C6160
I/O Card: 6160-DS3-IO
Slot 1 : STUC-8-TCPAM Slot 18: EMPTY
Slot 2 : EMPTY Slot 19: EMPTY
Slot 3 : EMPTY Slot 20: EMPTY
Slot 4 : EMPTY Slot 21: EMPTY
Slot 5 : EMPTY Slot 22: EMPTY
Slot 6 : EMPTY Slot 23: EMPTY
Slot 7 : EMPTY Slot 24: EMPTY
Slot 8 : EMPTY Slot 25: EMPTY
Slot 9 : STUC-8-TCPAM Slot 26: EMPTY
Slot 10: NI-2-DS3-DS3 Slot 27: EMPTY
Slot 11: EMPTY Slot 28: EMPTY
Slot 12: EMPTY Slot 29: EMPTY
Slot 13: EMPTY Slot 30: EMPTY
Slot 14: EMPTY Slot 31: EMPTY
Slot 15: EMPTY Slot 32: EMPTY
Slot 16: EMPTY Slot 33: EMPTY
Slot 17: EMPTY Slot 34: EMPTY
Fan Module: Present
Power Supply Module 1: 6160-PEM-DC
Power Supply Module 2: 6160-PEM-DC
dslam02-test.40nr#sh int atm0/1
ATM0/1 is up, line protocol is up
Hardware is ds3suni
MTU 4470 bytes, sub MTU 4470, BW 45000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Last input 00:00:00, output 00:00:04, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 3000 bits/sec, 9 packets/sec
5 minute output rate 1000 bits/sec, 1 packets/sec
7673 packets input, 406669 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
962 packets output, 50986 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
dslam02-test.40nr#sh int atm0/2
ATM0/2 is up, line protocol is up
Hardware is ds3suni
MTU 4470 bytes, sub MTU 4470, BW 45000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Last input 00:00:01, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
1293 packets input, 68529 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
1096 packets output, 58088 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
dslam02-test.40nr#sh log
dslam02-test.40nr#sh logging
Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns)
Console logging: level debugging, 59 messages logged
Monitor logging: level debugging, 0 messages logged
Buffer logging: level debugging, 59 messages logged
Logging Exception size (4096 bytes)
Trap logging: level informational, 71 message lines logged
Log Buffer (8192 bytes):
00:00:54: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) NI2 Software (NI2-DSL-M), Version 12.2(12)DA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Wed 23-Apr-03 11:55 by torowe
00:00:54: %SNMP-5-COLDSTART: SNMP agent on host dslam02-test.40nr is undergoing a cold start
00:00:54: %LINK-3-UPDOWN: Interface ATM0/0 to ATM0/1, changed state to up
00:00:54: %LINK-3-UPDOWN: Interface ATM0/2 to ATM0/3, changed state to down
00:00:54: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/1, changed state to up
00:00:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2 to ATM0/3, changed state to down
00:00:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up
00:00:54: %SYS-6-BOOTTIME: Time taken to reboot after reload = 946689358 seconds
00:00:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/1 to ATM1/8, changed state to down
00:00:56: %ATM-4-ILMICONFIGCHANGE: ILMI(ATM0/1): Restarting ATM signalling and ILMI. Peer Configuration change detected.
00:00:56: %ATM-5-ATMSOFTSTART: Restarting ATM signalling and ILMI on ATM0/1.
00:00:58: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up
00:01:03: %SLOT-3-MODULE_MISSING: ASSERT MAJOR Slot 1 Provisioned slot is empty
00:01:08: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 1 Provisioned slot is empty
00:01:08: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 1 Module was detected
00:01:08: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 9 Module was detected
00:01:08: %IPCOIR-5-CARD_LOADING: Loading card 9
00:01:08: %SUNI_QJET-3-YEL: CLEAR CRITICAL ATM0/2 Yellow Alarm Received
00:01:11: %LINK-3-UPDOWN: Interface ATM1/1 to ATM1/8, changed state to down
00:01:11: %LINK-3-UPDOWN: Interface ATM0/2, changed state to up
00:01:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM9/1 to ATM9/8, changed state to down
00:01:49: %LINK-3-UPDOWN: Interface ATM1/3, changed state to up
00:01:50: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/3, changed state to up
00:02:33: %ATMCORE-3-INTERNAL_ERROR: CTT row 3800 is internally created.
Please do not use this row for creating VCs.
Use only those rows listed in show running-config
00:02:34: %SYS-5-CONFIG_I: Configured from console by vty0 (192.168.11.16)
00:02:39: %CLOCKSW: Switching from System to ATM0/1 at prior 5
00:04:08: %SLOT-3-MODULE_DETECTED: CLEAR INFO Slot 9 Module was detected
00:04:08: %SLOT-3-MODULE_MISSING: ASSERT MAJOR Slot 9 Provisioned slot is empty
00:04:29: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 9 Provisioned slot is empty
00:04:29: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 9 Module was detected
00:04:32: %LINK-3-UPDOWN: Interface ATM9/1 to ATM9/8, changed state to down
00:07:41: %SLOT-3-MODULE_DETECTED: CLEAR INFO Slot 9 Module was detected
00:07:41: %SLOT-3-MODULE_MISSING: ASSERT MAJOR Slot 9 Provisioned slot is empty
00:07:42: %SLOT-3-MODULE_DETECTED: CLEAR INFO Slot 1 Module was detected
00:07:42: %SLOT-3-MODULE_MISSING: ASSERT MAJOR Slot 1 Provisioned slot is empty
00:07:44: %LINK-5-CHANGED: Interface ATM9/1 to ATM9/8, changed state to initializing
00:07:45: %LINK-5-CHANGED: Interface ATM1/1 to ATM1/8, changed state to initializing
00:07:46: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/3, changed state to down
00:08:13: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 1 Provisioned slot is empty
00:08:13: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 1 Module was detected
00:08:16: %LINK-3-UPDOWN: Interface ATM1/1 to ATM1/8, changed state to down
00:08:55: %LINK-3-UPDOWN: Interface ATM1/3, changed state to up
00:08:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/3, changed state to up
00:09:21: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 9 Provisioned slot is empty
00:09:21: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 9 Module was detected
00:09:24: %LINK-3-UPDOWN: Interface ATM9/1 to ATM9/8, changed state to down
00:10:14: %ATMCORE-3-INTERNAL_ERROR: CTT row 3800 is internally created.
Please do not use this row for creating VCs.
Use only those rows listed in show running-config
00:10:15: %SYS-5-CONFIG_I: Configured from console by vty0 (192.168.11.16)
00:10:33: %ATMCORE-3-INTERNAL_ERROR: CTT row 3800 is internally created.
Please do not use this row for creating VCs.
Use only those rows listed in show running-config
dslam02-test.40nr#
Thank you,
Mihai
