Re: 3640 NM-2FE2W card problem

yatao · ‎01-08-2002

Recently I upgraded a 3640 from 12.0.5 to 12.1.7, and notice that IOS doesn't regconize the NM-2FE2W card any more, it says "no iomem table entry for PA(0xD8) in slot0". run "show diag":

fwa>sh diag

Slot 0:

Unknown (type 216) Port adapter

Port adapter is disabled

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.0

Part Number : 800-04797-01

Board Revision : E0

Deviation Number : 0-0

Fab Version : 04

PCB Serial Number : JAB04130H1R

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 D8 41 01 00 C0 46 03 20 00 12 BD 01

0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 4A 41 42 30

0x20: 34 31 33 30 48 31 52 03 00 81 00 00 00 00 04 00

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

And this problem happens in another 3640 with 12.0.7. Anyone has idea what is the problem? How to fix it?

Thanks,

Yatao

srehan · ‎01-08-2002

You need to have 121.1T or later version and have ip plus feature set to support ISL trunking on fast ethernet. Send sh ver please

yatao · ‎01-08-2002

Thanks for your quick response. Here is the output:

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-JO3S56I-M), Version 12.1(7), RELEASE SOFTWARE (fc1)

Compiled Fri 23-Feb-01 03:21 by kellythw

Image text-base: 0x60008940, data-base: 0x61442000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

fwa uptime is 2 hours, 7 minutes

System returned to ROM by reload

System image file is "flash:c3640-jo3s56i-mz.121-7.bin"

cisco 3640 (R4700) processor (revision 0x00) with 60416K/5120K bytes of memory.

Processor board ID 15636356

R4700 CPU at 100Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

TN3270 Emulation software.

2 Ethernet/IEEE 802.3 interface(s)

1 FastEthernet/IEEE 802.3 interface(s)

4 Serial network interface(s)

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Could you recommend a IOS version?

Thanks again

Yatao

srehan · ‎01-08-2002

You need to upgrade the version in order to support that card , 12.1T or hight version in T train or if you want. to stay with main lin version then 12.2 will be okay .

Thanks