10-13-2004 04:05 AM - edited 03-02-2019 07:13 PM
5509 with 32 MB of DRAM a 8 MB of FLASH on Supervisor III G with following modules:
Slot Ports Module-Type Model
---- ----- ------------------------- ---------
1 2 1000BaseX Supervisor IIIG WS-X5550
1 1 Route Switch Feature Card WS-F5541
2 2 OC12 Dual PHY MMF WS-X5161
3 Gigabit Ethernet Ext WS-X5410
4 9 Gigabit Ethernet WS-X5410
5 Gigabit Ethernet Ext WS-X5410
6 9 Gigabit Ethernet WS-X5410
is running catos 5.x on supervisor and ios 12.0 on atm card. For upgrade of ios on atm card there is a requirement for 64MB of DRAM and 16MB of FLASH, but I can not find any information that there were sold Supervisors III G with this memory or there was any upgrade kits? What is the max. of DRAM and FLASH for Sup. III G? What is the reccomended CatOS and IOS for above 5509 configuration?
Thanks for any ideas.
Solved! Go to Solution.
10-13-2004 06:26 AM
You can upgrade your ATM blade with existing memory on it. The software download page gives you the generic memory requirements. There is no hardware upgrade needed.
10-13-2004 04:27 AM
You can upgrade to the latest 6.4(13) on Sup3G with 32MB DRAM. There is no upgrade option for Sup3G DRAM. The release notes has the memory requirement
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat5000/c5krn/sw_rns/78_11304.htm#wp53565
For ATM Module IOS, you can upgrade to 12.1(23)E1 after you upgrade memory. For RSFC, we have a GD release 12.1(25). Check the release notes for known issues.
10-13-2004 05:28 AM
Many thanks for your clear answer regarding memory and catos on Sup. IIIG, but I do not understand your memory upgrade for ATM Module IOS - there is a requirement to HW upgrade memory on this module to use 12.1.(23)E1 IOS? Memory requirements in release notes for IOS for ATM Module are requirements for memory on this board or the supervisor? My sh ver from ATM module looks like that:
Cisco Internetwork Operating System Software
IOS (tm) C5kATM Software (TKE-A-M), Version 12.0(9)W5(17a) RELEASE SOFTWARE
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Thu 04-May-00 21:50 by
Image text-base: 0x40010000, data-base: 0x402A26E0
ROM: System Bootstrap, Version 12.0(9)W5(17a) RELEASE SOFTWARE
Cat_Atm_Vs uptime is 6 weeks, 5 days, 14 hours, 34 minutes
System restarted by power-on at 21:25:35 UTC Mon Jan 5 2004
Running default software
cisco C5kTKE (68ec030) processor (revision 0x00) with 22784K bytes of memory.
Processor board ID 1610612736, with hardware revision
Last reset from
Authorized for ATM software set. (0x0)
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
511K bytes of non-volatile configuration memory.
Configuration register is 0x1901
Is my memory on ATM Module ok for 12.1(23) or hw upgrade is required? Once again thanks for one more answer.
10-13-2004 06:26 AM
You can upgrade your ATM blade with existing memory on it. The software download page gives you the generic memory requirements. There is no hardware upgrade needed.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: