11-09-2002 09:57 AM - edited 03-02-2019 02:46 AM
Hi
I have a 827h router running the ip ios (c820-oy6-mz.122-4.YA2.bin). This works fine.
If however i upgrade the ios to include the ip/fw/des ios (c820-k8osy6-mz.122-2.T4.bin) it immediately stops working. the atm0 interface shows down and line protocol down.
I have tried all the obvious things to no avail. One thing i have noticed is that in config mode if i change to the atm0 interface I have no option to enter commands starting with 'dsl' the main one that i have noticed is missing is "dsl operating-mode auto". This is a command that i have seen in every sample config posted on cisco.com and on other sites.
Router Config
- - - - - - - - - - - - - - - - - - - - - - - - - -
version 12.2
no parser cache
service single-slot-reload-enable
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname KahunaRO
!
logging buffered 4096 debugging
logging rate-limit console 10 except errors
!
username pagec password 0 xxxxxxxxxxxx
ip subnet-zero
!
ip inspect name Dialer_0 tcp
ip inspect name Dialer_0 udp
ip inspect name Dialer_0 cuseeme
ip inspect name Dialer_0 ftp
ip inspect name Dialer_0 h323
ip inspect name Dialer_0 rcmd
ip inspect name Dialer_0 realaudio
ip inspect name Dialer_0 streamworks
ip inspect name Dialer_0 vdolive
ip inspect name Dialer_0 sqlnet
ip inspect name Dialer_0 tftp
ip ssh time-out 120
ip ssh authentication-retries 3
no ip dhcp-client network-discovery
!
!
!
!
interface Ethernet0
ip address 192.168.xxx.200 255.255.255.0
ip access-group 102 in
ip nat inside
!
interface Virtual-Template1
no ip address
!
interface ATM0
no ip address
no atm ilmi-keepalive
!
interface ATM0.1 point-to-point
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface Dialer0
bandwidth 640
ip address xxx.xxx.xxx.xxx 255.255.255.0
ip access-group 101 in
no ip redirects
no ip unreachables
ip nat outside
ip inspect Dialer_0 out
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp chap hostname me@mydsl.net
ppp chap password 7 141C1D05030C2B
ppp ipcp dns request
!
ip nat inside source list 1 interface Dialer0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
ip http server
!
access-list 1 permit xxx.xxx.xxx.0 0.0.0.255
access-list 23 permit xxx.xxx.xxx.0 0.0.0.255
access-list 101 remark Traffic allowed to enter the router from Internet
access-list 101 deny ip 10.0.0.0 0.255.255.255 any
access-list 101 deny ip 172.16.0.0 0.15.255.255 any
access-list 101 deny ip 192.168.0.0 0.0.255.255 any
access-list 101 deny ip any host 255.255.255.255
access-list 101 permit udp any eq isakmp any eq isakmp
access-list 101 permit gre any any
access-list 101 permit icmp any any unreachable
access-list 101 permit icmp any any echo-reply
access-list 101 permit icmp any any packet-too-big
access-list 101 permit icmp any any time-exceeded
access-list 101 permit icmp any any traceroute
access-list 101 permit icmp any any administratively-prohibited
access-list 101 permit icmp any any echo
access-list 101 deny ip any any log
access-list 102 remark Traffic allowed to enter the router from the Ethernet
access-list 102 deny udp any any eq tftp
access-list 102 permit ip xxx.xxx.xxx.0 0.0.0.255 any
access-list 102 permit ip any host xxx.xxx.xxx.254
access-list 102 permit ip any host 255.255.255.255
access-list 102 deny ip any any log
dialer-list 1 protocol ip permit
!
line con 0
stopbits 1
line vty 0 4
login
!
scheduler max-task-time 5000
end
- - - - - - - - - - - - - - - - - - - - - - - - - -
Does anyone have any advice on what could be causing this and if there are any workarounds.
any help/advice would be apreciated as this is driving me nuts
11-11-2002 12:28 PM
The H model uses a different ADSL chipset than the 827 (newer version), so the "T" train is not yet supported. This setup should work fine with any 12.2(4)YA or newer code.
11-12-2002 12:46 AM
Aaaah so that's it - I logged a case with TAC after I found that it would work with YJ or YJ1 and not T4/T5 but got nowhere fast.
11-16-2002 07:36 AM
Thanks a lot, that worked a treat. I've been tearing my hair out over this.
chris
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide