Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
6412
Views
0
Helpful
11
Replies

9130axi can't join 9800-80 WLC write error - No space left on device

Go to solution
Adam.Elrafih
Level 1
Level 1

‎12-09-2022 12:59 PM

Hello,

I have been running issues trying to move a 9130axi AP from airos wlc running 8.10 to a 9800 running v 17.9.1

The AP is able to join the wlc8540 but can't complete the software upgrade when attempting to join the 9800. After downloading for some time, it eventually displays that there is insufficent space. I was unable to remove the backup image on the AP. Does anyone know how to do this?

Logs from failed download:

Inititial check from log:

[*12/09/2022 20:25:23.2525] upgrade.sh: /tmp space: OK available 80516, required 40000

After downloading for a while, we see the following before auto reattempt.

Read timed out

[*12/09/2022 20:36:21.9116] sh: write error: No space left on device
[*12/09/2022 20:36:21.9166] tar: write error: No space left on device

AP Version: (Ideally would like to remove one of these versions)
AP Running Image : 8.10.162.0
Primary Boot Image : 8.10.162.0
Backup Boot Image : 8.10.130.0

AP70F0.960C.1714#show filesystems
Filesystem Size Used Available Use% Mounted on
devtmpfs 883.0M 0 883.0M 0% /dev
/sysroot 885.6M 201.7M 683.8M 23% /
tmpfs 1.0M 44.0K 980.0K 4% /dev/shm
tmpfs 885.6M 0 885.6M 0% /run
tmpfs 885.6M 0 885.6M 0% /sys/fs/cgroup
/dev/ubivol/part1 372.1M 57.2M 314.9M 15% /part1
/dev/ubivol/part2 520.1M 59.8M 460.3M 11% /part2
none 80.0M 1.2M 78.8M 2% /tmp
none 1.0M 44.0K 980.0K 4% /dev/shm

 

 

2 people had this problem
Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
Adam.Elrafih
Level 1
Level 1

‎12-12-2022 02:10 PM

Issue resolved by joining AP to another WLC 9800 running SW 17.7.1

View solution in original post

0 Helpful
11 Replies 11

Go to solution
balaji.bandi
Hall of Fame
Hall of Fame

‎12-09-2022 02:32 PM

how about reset and manually joining the AP to Cat 9800 controller?

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

0 Helpful

Go to solution
Adam.Elrafih
Level 1
Level 1
In response to balaji.bandi

‎12-09-2022 03:02 PM

H Balaji, thanks for the reply. I did try the factory reset, same issue exists. I also tried switching the primary image with the backup but it did not work either.

0 Helpful

Go to solution
Adam.Elrafih
Level 1
Level 1

‎12-09-2022 03:00 PM

H Balaji, thanks for the reply. I did try the factory reset, same issue exists. I also tried switching the primary image with the backup but it did not work either.

0 Helpful

Go to solution
balaji.bandi
Hall of Fame
Hall of Fame
In response to Adam.Elrafih

‎12-09-2022 03:04 PM

Can you able to post complete logs to understand what went wrong?

also, suggest contacting TAC

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

0 Helpful

Go to solution
Adam.Elrafih
Level 1
Level 1
In response to balaji.bandi

‎12-09-2022 03:39 PM

[*12/09/2022 23:02:27.8894] CAPWAP State: Discovery
[*12/09/2022 23:02:27.8915] Discovery Request sent to <WLC_IP>, discovery type STATIC_CONFIG(1)
[*12/09/2022 23:02:27.8917] IP DNS query for CISCO-CAPWAP-CONTROLLER.cg.shawcable.net
[*12/09/2022 23:02:27.9449] Discovery Request sent to <WLC_IP>, discovery type STATIC_CONFIG(1)
[*12/09/2022 23:02:27.9464] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*12/09/2022 23:02:27.9479] Discovery Request sent to ff02::18c, discovery type UNKNOWN(0)
[*12/09/2022 23:02:27.9480] Discovery Response from <WLC_IP>
[*12/09/2022 23:02:27.9552] Discovery Response from <WLC_IP>
[*12/09/2022 23:02:34.8084] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Discovery(2).
[*12/09/2022 23:02:37.0002]
[*12/09/2022 23:02:37.0003] CAPWAP State: DTLS Setup
[*12/09/2022 23:02:37.6882]
[*12/09/2022 23:02:37.6882] CAPWAP State: Join
[*12/09/2022 23:02:37.6905] Sending Join request to <WLC_IP> through port 5264
[*12/09/2022 23:02:37.7037] Join Response from <WLC_IP>
[*12/09/2022 23:02:37.7037] AC accepted join request with result code: 0
[*12/09/2022 23:02:37.7044] Received wlcType 0, timer 30
[*12/09/2022 23:02:37.7044] TLV ID 2216 not found
[*12/09/2022 23:02:37.7044] TLV-DEC-ERR-1: No proc for 2216
[*12/09/2022 23:02:37.7336]
[*12/09/2022 23:02:37.7336] CAPWAP State: Image Data
[*12/09/2022 23:02:37.7339] AP image version 8.10.130.0 backup 8.10.162.0, Controller 17.9.1.8
[*12/09/2022 23:02:37.7339] Version does not match.
[*12/09/2022 23:02:37.7591] upgrade.sh: Script called with args:[PRECHECK]
[*12/09/2022 23:02:37.7916] do PRECHECK, part1 is active part
[*12/09/2022 23:02:37.8136] upgrade.sh: /tmp space: OK available 79652, required 40000
[*12/09/2022 23:02:37.8140] wtpImgFileReadRequest: request ap1g6a, local /tmp/part.tar
[*12/09/2022 23:02:37.8152] Image Data Request sent to <WLC_IP>, fileName [ap1g6a], slaveStatus 0
[*12/09/2022 23:02:37.8252] Image Data Response from <WLC_IP>
[*12/09/2022 23:02:37.8252] AC accepted join request with result code: 0
[*12/09/2022 23:02:37.8291] <..........................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:03:35.5062] ........................
[*12/09/2022 23:04:28.6843] ..Invalid event 56 & state 10 combination.
[*12/09/2022 23:04:31.6186] Failed to handle timer message.
[*12/09/2022 23:04:33.0225] .Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:04:35.1565] .....................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:05:19.1925] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:05:19.4018] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:05:20.9329] .......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:05:36.2186] ...................
[*12/09/2022 23:06:17.4892] ........Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:06:34.9001] ............................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:07:35.6958] ..............
[*12/09/2022 23:08:05.7714] .......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:08:19.1925] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:08:19.4019] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:08:21.1718] .......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:08:36.4498] ...........................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:09:35.3808] .........
[*12/09/2022 23:09:54.8955] ...................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:10:35.4580] .....................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:11:19.1925] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:11:19.4020] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:11:19.7910] ........Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:11:36.8119] ..
[*12/09/2022 23:11:41.2303] ..........................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:12:36.1240] ........................
[*12/09/2022 23:13:28.3482] ....Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:13:37.0600] ........> 84039680 bytes, 62484 msgs, 45 last
[*12/09/2022 23:13:53.3101] Last block stored, IsPre 0, WriteTaskId 0
[*12/09/2022 23:13:53.3102] Image transfer completed from WLC, last 1
[*12/09/2022 23:13:53.3104] wtpProcessImageDataRequest(10): fileName ap1g6a, pre 0
[*12/09/2022 23:13:53.3354] upgrade.sh: Script called with args:[PREDOWNLOAD]
[*12/09/2022 23:13:53.3669] do PREDOWNLOAD, part1 is active part
[*12/09/2022 23:13:53.3814] upgrade.sh: Start doing upgrade arg1=PREDOWNLOAD arg2= arg3= ...
[*12/09/2022 23:13:53.4381] upgrade.sh: Using image /tmp/part.tar on axel-qca ...
[*12/09/2022 23:13:53.4383] sh: write error: No space left on device
[*12/09/2022 23:13:53.4436] tar: write error: No space left on device
[*12/09/2022 23:13:53.4718] upgrade.sh: ERROR: Image type mismatch. Expected:ap1g6a Got:
[*12/09/2022 23:13:53.4890] upgrade.sh: Cleanup for do_upgrade...
[*12/09/2022 23:13:53.5049] upgrade.sh: /tmp/upgrade_in_progress cleaned
[*12/09/2022 23:13:53.5187] upgrade.sh: Cleanup tmp files ...
[*12/09/2022 23:13:53.5562] capwap-upgrade script returned failure when calling PREDOWNLOAD.
[*12/09/2022 23:13:53.5564] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:13:53.5564] CAPWAP SM handler: Failed to process message type 15 state 10.
[*12/09/2022 23:13:53.5564] Failed to handle capwap control message from controller - status 2
[*12/09/2022 23:13:53.5565] Failed to process encrypted capwap packet 0x5598030000 from <WLC_IP>
[*12/09/2022 23:13:53.5565] Failed to send capwap message 0 to the state machine. Packet already freed.
[*12/09/2022 23:14:04.8642] Re-Tx Count=1, Max Re-Tx Value=5, SendSeqNum=25, NumofPendingMsgs=1
[*12/09/2022 23:14:04.8642]
[*12/09/2022 23:14:07.7152] Re-Tx Count=2, Max Re-Tx Value=5, SendSeqNum=25, NumofPendingMsgs=1
[*12/09/2022 23:14:07.7152]
[*12/09/2022 23:14:10.5661] Re-Tx Count=3, Max Re-Tx Value=5, SendSeqNum=25, NumofPendingMsgs=1
[*12/09/2022 23:14:10.5662]
[*12/09/2022 23:14:13.4171] Re-Tx Count=4, Max Re-Tx Value=5, SendSeqNum=25, NumofPendingMsgs=1
[*12/09/2022 23:14:13.4171]
[*12/09/2022 23:14:16.2681] Re-Tx Count=5, Max Re-Tx Value=5, SendSeqNum=25, NumofPendingMsgs=1
[*12/09/2022 23:14:16.2681]
[*12/09/2022 23:14:19.1191] Max retransmission count exceeded, going back to DISCOVER mode.
[*12/09/2022 23:14:19.1191] Dropping msg CAPWAP_ECHO_REQUEST, type = 1, len = 0, eleLen = 8, sendSeqNum = 25
[*12/09/2022 23:14:19.1387]
[*12/09/2022 23:14:19.1387] CAPWAP State: DTLS Teardown
[*12/09/2022 23:14:19.1530] Aborting image download(0x0): Dtls cleanup, ap1g6a
[*12/09/2022 23:14:19.2279] upgrade.sh: Script called with args:[ABORT]
[*12/09/2022 23:14:19.2608] do ABORT, part1 is active part
[*12/09/2022 23:14:19.2822] upgrade.sh: Cleanup tmp files ...
[*12/09/2022 23:14:19.3050] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/09/2022 23:14:19.3050] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/09/2022 23:14:23.8891]
[*12/09/2022 23:14:23.8891] CAPWAP State: Discovery
[*12/09/2022 23:14:23.8917] Discovery Request sent to <WLC_IP>, discovery type STATIC_CONFIG(1)
[*12/09/2022 23:14:23.8919] IP DNS query for CISCO-CAPWAP-CONTROLLER.cg.shawcable.net
[*12/09/2022 23:14:23.9468] Discovery Request sent to <WLC_IP>, discovery type STATIC_CONFIG(1)
[*12/09/2022 23:14:23.9483] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*12/09/2022 23:14:23.9628] Discovery Request sent to ff02::18c, discovery type UNKNOWN(0)
[*12/09/2022 23:14:23.9629] Discovery Response from <WLC_IP>
[*12/09/2022 23:14:23.9634] Discovery Response from <WLC_IP>
[*12/09/2022 23:14:34.0003]
[*12/09/2022 23:14:34.0003] CAPWAP State: DTLS Setup
[*12/09/2022 23:14:34.6939]
[*12/09/2022 23:14:34.6939] CAPWAP State: Join
[*12/09/2022 23:14:34.6968] Sending Join request to <WLC_IP> through port 5264
[*12/09/2022 23:14:34.7184] Join Response from <WLC_IP>
[*12/09/2022 23:14:34.7185] AC accepted join request with result code: 0
[*12/09/2022 23:14:34.7191] Received wlcType 0, timer 30
[*12/09/2022 23:14:34.7192] TLV ID 2216 not found
[*12/09/2022 23:14:34.7192] TLV-DEC-ERR-1: No proc for 2216
[*12/09/2022 23:14:34.7419]
[*12/09/2022 23:14:34.7419] CAPWAP State: Image Data
[*12/09/2022 23:14:34.7422] AP image version 8.10.130.0 backup 8.10.162.0, Controller 17.9.1.8
[*12/09/2022 23:14:34.7422] Version does not match.
[*12/09/2022 23:14:34.7680] upgrade.sh: Script called with args:[PRECHECK]
[*12/09/2022 23:14:34.8008] do PRECHECK, part1 is active part
[*12/09/2022 23:14:34.8220] upgrade.sh: /tmp space: OK available 79600, required 40000
[*12/09/2022 23:14:34.8224] wtpImgFileReadRequest: request ap1g6a, local /tmp/part.tar
[*12/09/2022 23:14:34.8235] Image Data Request sent to <WLC_IP>, fileName [ap1g6a], slaveStatus 0
[*12/09/2022 23:14:34.8347] Image Data Response from <WLC_IP>
[*12/09/2022 23:14:34.8348] AC accepted join request with result code: 0
[*12/09/2022 23:14:34.8394] <Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:14:37.3913] ...........................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:15:37.0086] .......................
[*12/09/2022 23:16:28.6108] Invalid event 56 & state 10 combination.
[*12/09/2022 23:16:28.6108] Failed to handle timer message.
[*12/09/2022 23:16:29.9246] ...Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:16:36.8680] ...................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:17:19.8183] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:17:20.0279] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:17:20.9026] .......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:17:37.3379] .....................
[*12/09/2022 23:18:26.5822] .....Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:18:38.1614] ..........................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:19:38.5983] ..................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:20:19.8183] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:20:20.0280] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:20:21.4286] .
[*12/09/2022 23:20:23.9303] ......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:20:37.9464] ..........................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:21:39.3385] ..................
[*12/09/2022 23:22:21.7704] .......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:22:38.5858] ..................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:23:19.8183] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:23:20.0280] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:23:22.0229] .......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:23:38.9433] ..................
[*12/09/2022 23:24:22.0133] .......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:24:38.4032] .........................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:25:38.3639] ..................
[*12/09/2022 23:26:19.7705] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:26:19.8183] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:26:20.0281] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:26:21.6157] .......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:26:38.2303] .....> 84039680 bytes, 62484 msgs, 45 last
[*12/09/2022 23:26:48.7774] Last block stored, IsPre 0, WriteTaskId 0
[*12/09/2022 23:26:48.7776] Image transfer completed from WLC, last 1
[*12/09/2022 23:26:48.7777] wtpProcessImageDataRequest(10): fileName ap1g6a, pre 0
[*12/09/2022 23:26:48.8033] upgrade.sh: Script called with args:[PREDOWNLOAD]
[*12/09/2022 23:26:48.8356] do PREDOWNLOAD, part1 is active part
[*12/09/2022 23:26:48.8498] upgrade.sh: Start doing upgrade arg1=PREDOWNLOAD arg2= arg3= ...
[*12/09/2022 23:26:48.9029] upgrade.sh: Using image /tmp/part.tar on axel-qca ...
[*12/09/2022 23:26:48.9031] sh: write error: No space left on device
[*12/09/2022 23:26:48.9082] tar: write error: No space left on device
[*12/09/2022 23:26:48.9338] upgrade.sh: ERROR: Image type mismatch. Expected:ap1g6a Got:
[*12/09/2022 23:26:48.9505] upgrade.sh: Cleanup for do_upgrade...
[*12/09/2022 23:26:48.9666] upgrade.sh: /tmp/upgrade_in_progress cleaned
[*12/09/2022 23:26:48.9804] upgrade.sh: Cleanup tmp files ...
[*12/09/2022 23:26:49.0190] capwap-upgrade script returned failure when calling PREDOWNLOAD.
[*12/09/2022 23:26:49.0192] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/09/2022 23:26:49.0193] CAPWAP SM handler: Failed to process message type 15 state 10.
[*12/09/2022 23:26:49.0193] Failed to handle capwap control message from controller - status 2
[*12/09/2022 23:26:49.0193] Failed to process encrypted capwap packet 0x5597fc6000 from <WLC_IP>
[*12/09/2022 23:26:49.0193] Failed to send capwap message 0 to the state machine. Packet already freed.
[*12/09/2022 23:26:58.8758] Re-Tx Count=1, Max Re-Tx Value=5, SendSeqNum=27, NumofPendingMsgs=1
[*12/09/2022 23:26:58.8758]
[*12/09/2022 23:27:01.7267] Re-Tx Count=2, Max Re-Tx Value=5, SendSeqNum=27, NumofPendingMsgs=1
[*12/09/2022 23:27:01.7267]
[*12/09/2022 23:27:04.5777] Re-Tx Count=3, Max Re-Tx Value=5, SendSeqNum=27, NumofPendingMsgs=1
[*12/09/2022 23:27:04.5777]
[*12/09/2022 23:27:07.4286] Re-Tx Count=4, Max Re-Tx Value=5, SendSeqNum=27, NumofPendingMsgs=1
[*12/09/2022 23:27:07.4287]
[*12/09/2022 23:27:10.2796] Re-Tx Count=5, Max Re-Tx Value=5, SendSeqNum=27, NumofPendingMsgs=1
[*12/09/2022 23:27:10.2796]
[*12/09/2022 23:27:13.1305] Max retransmission count exceeded, going back to DISCOVER mode.
[*12/09/2022 23:27:13.1306] Dropping msg CAPWAP_ECHO_REQUEST, type = 1, len = 0, eleLen = 8, sendSeqNum = 27
[*12/09/2022 23:27:13.1499]
[*12/09/2022 23:27:13.1499] CAPWAP State: DTLS Teardown
[*12/09/2022 23:27:13.1634] Aborting image download(0x0): Dtls cleanup, ap1g6a
[*12/09/2022 23:27:13.2418] upgrade.sh: Script called with args:[ABORT]
[*12/09/2022 23:27:13.2744] do ABORT, part1 is active part
[*12/09/2022 23:27:13.2944] upgrade.sh: Cleanup tmp files ...
[*12/09/2022 23:27:13.3166] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/09/2022 23:27:13.3166] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).

0 Helpful

Go to solution
Leo Laohoo
Hall of Fame
Hall of Fame

‎12-09-2022 03:25 PM

Post the complete output to the command "sh boot".

0 Helpful

Go to solution
Adam.Elrafih
Level 1
Level 1
In response to Leo Laohoo

‎12-09-2022 03:30 PM

AP-9130#show boot
BOOT path-list: part1
Console Baudrate: 9600
Enable Break: yes
Manual Boot: no
Memory Debug: no
Crashkernel:
Debug init: 0
AP-9130#

0 Helpful

Go to solution
Leo Laohoo
Hall of Fame
Hall of Fame
In response to Adam.Elrafih

‎12-09-2022 03:42 PM

From the AP, do the following: 

config boot path 2

Reboot the AP.

0 Helpful

Go to solution
Adam.Elrafih
Level 1
Level 1
In response to Leo Laohoo

‎12-12-2022 10:23 AM

Thanks Leo, same issue after the switch.
AP-9130#show boot
BOOT path-list: part2
Console Baudrate: 9600
Enable Break: yes
Manual Boot: no
Memory Debug: no
Crashkernel: no
Debug init: 0


[*12/12/2022 18:13:37.3639] Image transfer completed from WLC, last 1
[*12/12/2022 18:13:37.3640] wtpProcessImageDataRequest(10): fileName ap1g6a, pre 0
[*12/12/2022 18:13:37.3894] upgrade.sh: Script called with args:[PREDOWNLOAD]
[*12/12/2022 18:13:37.4207] do PREDOWNLOAD, part2 is active part
[*12/12/2022 18:13:37.4349] upgrade.sh: Start doing upgrade arg1=PREDOWNLOAD arg2= arg3= ...
[*12/12/2022 18:13:37.4888] upgrade.sh: Using image /tmp/part.tar on axel-qca ...
[*12/12/2022 18:13:37.4890] sh: write error: No space left on device
[*12/12/2022 18:13:37.4961] tar: write error: No space left on device
[*12/12/2022 18:13:37.5237] upgrade.sh: ERROR: Image type mismatch. Expected:ap1g6a Got:
[*12/12/2022 18:13:37.5400] upgrade.sh: Cleanup for do_upgrade...
[*12/12/2022 18:13:37.5557] upgrade.sh: /tmp/upgrade_in_progress cleaned
[*12/12/2022 18:13:37.5695] upgrade.sh: Cleanup tmp files ...
[*12/12/2022 18:13:37.6094] capwap-upgrade script returned failure when calling PREDOWNLOAD.

 

0 Helpful

Go to solution
Adam.Elrafih
Level 1
Level 1

‎12-12-2022 02:10 PM

Issue resolved by joining AP to another WLC 9800 running SW 17.7.1

0 Helpful

Go to solution
balaji.bandi
Hall of Fame
Hall of Fame
In response to Adam.Elrafih

‎12-12-2022 02:14 PM

Looks like some new AP of the Cat 9K models needs a minimum version 17.8.X

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

0 Helpful
Customers Also Viewed These Support Documents

Review Cisco Networking for a $25 gift card