Other Network Architecture Subjects

Hi, I'm looking for some answer's to some questions i have regarding STP, vlan-Load Balancing and Uplink Fast.I have 4 3750-24TS switches.2 of these switches are at Site A and the Other 2 at Site B.The Two switches at each site are connected via the ...

folksanyone know the password recovery procedure for a 2821 integrated service routerthe link http://lbj.cisco.com/push_targets1/ucdit/cc/td/doc/product/access/acs_mod/2800/sw/tac_tsa/trtips.htmjust times out on mei'm using hyperterminal to consoleth...

No replies last time.With the following config I can ping both to and from hosts on the Office LAN to and from the Outside Network, but not out to the ISP.Traffic moves fine from Office LAN through NAT to and from ISP.But from Outside Network I can o...

Hi, We are trying to understand the setup on two distribution 6509 switches running HSRP. Can anyone help.SHOW STANDBY BRIEF references Vlan81 on bothdevices as saying this Vlan81 is active/local , whereas all the other Vlans are either standby/activ...

Hi,I want to know if we can choose the time between two ntp requests.and if yes, how? thx in advance

I have a 2620 connected to a 1721 on a leased point2 point. I can ping and manage either box from the other. The 2620 can get to the internet via a sonicwall. The 1710 cannot. The 2620 ethernet port is 192.168.1.6 with a serial0/0 of 10.1.0.1. T...

I have a Cisco 2611XM router running Cisco IOS 12.3(6). I'm trying to figure out how to view traffic statistics using the debug command. Any ideas? The problem I'm having is that I want to verify that https traffic is, in fact, passing from one in...

I am running C6K in native mode resulting in an image size well above 32 MB. FTP transer works great but I would still like to use TFTP (customer). With a block-size of more than 512 Byte, e.g. 1500 Byte, it should work. I observed that the IOS (12.2...

Does anyone know how the L3 switching performance of a Cat4006(Supervisor 2) with 4232 L3 card would compare against a cat5500(Supervisor3) with RSM running MLS. I realise some of this kit is quite old but need to deploy at a mediun sized site and I ...

I have a flat network with a bunch of 2950's connected to a 3550. When I utilize Ghost in either broadcast or multicast mode to image workstations my network grinds to a halt. I'm aware that all interfaces are being flooded with the traffic. Not sure...

which L2 cisco switch supports MAC/IP/Protocol based VLAN?

I have 2 vlans on a single switch with the same IP address range (I must use the same) 10.101.11.0/24.the switch is connected to a router. I want to use NAT for both vlans with a single public address, how do I do it?

Dear All;I have Switch Cisco 4006 with Routing blade (4232-L3 blade); Witch configured for 3 VLANs, vlan 2 and 3 is picking ip address from DHCP server connected to VLAN3 I had creat one more VLAN (vlan4) and configured this vlan to pick ip address f...

I would like to upgrade an MSFC2 ROMMON to 122-17r.S1.Router#sho rom-monitor slot 2 rpRegion F1: INVALIDRegion F2: INVALIDCurrently running ROMMON from S (Gold) region1.Is this possible from Sup-slot0:?2.S (Gold) region is not upgradeable. Correct?3 ...

I have workstations in seperate VLAN's from our server farm. I have an intermittent problem with the workstations finding our Novell servers during login. When the user retries one or more times they will be able to login normally. The workstations a...