Hi Experts, Would like to clear a doubt. With a setup of two 9K series Nexus Switches running vPC peer link between them. A server is connected at access end of these switches. Just taking example. Switch-A and Switch-B are interconnected and ...
Forum Posts
Hi guys I trying to figure out how to enable egress traffic in a icmp flow Here the scenario, 2 routers Fa0/0 Fa0/0 RA -----------...
We are looking into installing stealth watch on our 4331s as a container on the NIM 200GB SSD card. I was curious if anyone has done this and how well does it work?
Resolved! VTP pruning not changing
Hello, My VTP server is running, when I add a new vlan it gets added to all client switches. But when enabling or disabling vtp pruning it doen't get propagated or values do not change on domain switches. Any idea why this is happening? VTP Server:...
Hi everybody,i want to write my ccdp certification and i want to confirm and verify the exam code for this exam.i currently have valid ccna, ccda, and ccnp certificication..please advise on the exam code for the ccdp cert?brsam
Resolved! IPSEC Lan to Lan to Internet
Hi I have a requirement to implement an IP-Sec service like the attached pic. Due to a 3rd party LAN that carries traffic I would like a IPSec tunnel between two routers. The end users will need internet ( NAT to say a 192.168.1.x). Does anyone have...
This is the example build I am trying to setup. There will be 3 firewalls (Internal Systems, HQ, and Branch). The Internal System Firewall is behind another firewall that is connected to our ISP. The internal Systems firewall does not have a d...
Resolved! VRFs and Vlans
Hi! I have a bit of a confusion here. I understand that vrfs are analog to vlans in means of separating traffic of layer 3 and layer 2, right? If this is correct, would create a VRF in a ML Switch that will only have an access port to a host and anot...
This topic is a chance to discuss more about the the Web of Things (WoT), from its definition and architecture, to its main components, scripting, and use cases samples. The WoT allows the integration of real-world objects not only to the Internet, b...
i have a case here, i have two vlans, one is vlan 10, 192.168.10.0/24. another is vlan 100, 192.168.100.0/24. i design to block vlan 10 to talk to vlan 100 but allow vlan 100 to reach vlan 10. how can i achieve this? i tried access list, but didn't w...
Hi I want to get help for Air print. I configured the ISR 1100, VLAN 3 for Print and VLAN 7 for a Wireless client (iPad). Now the issue is the iPad (VLAN7) cannot find the printer (VLAN3) by AirPrint. ============================================...
How to configure a Cisco 2811 2800 Series Router using a NM-16A or NM-32A Async Module as a Terminal Server Please let me know if there is anything I need to correct. I'm posting this to help others and to grow my own skills. The examples below are u...
Hi,I am setting up a broadband architechture using freeradius and cisco router as a NAS. I am unable to disconnect PPPoE sessions using freeradius.Can you assist for PoD or best possible method to acheive it? It would be a great hekp,
Hello guys I just bought hard copy of the below book "optimal-routing-design" , pls help me ,what is the best way to study this book in order to get the maximum benefits out of it , do i need to memorized like i did in my university study :( h...
hello @hector.grajales1 if your tunnel shows up on both sides, then you should be able to ping both tunnel interfaces, is this true? also, if you are using PBR, and traffic is not matching your ACL, you might need to check the ACL format. you c...
Recognize Your Peers
.jpg "VIP Community Legend"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
