First, this all worked once on a previous core that was a 4500 on Campus1. Config was transferred to a 9500 when we upgraded. Most people seem to think that it stopped working with the move to the 9500 from the 4500.Core switch (Campus1) is a 9500-...
Hi guys.Need your help!!!Got a router for a day cisco , and was tasked to connect the router through a router that is Magenta Router and Cisco Router. I also connected a switch which comes from cisco. Tried to configure cisco router , 2 interfaces.IN...
Hi all, I know that with vtp version 3, the problem has been solved that a CLIENT switch with a higher revision number than a SERVER switch with a lower revision number, the vlan database of the SERVER is not updated by the CLIENT.But is it really so...
Hi allI have a particular request from a customer. Currently, there is a CISCO Switch 2960 configured with 3 vlans( 10,20,30) on the vlans 10 & 20 will be the computers, printers etc. for the users, and on vlan 30 will be the servers(DHCP, DNS,FTP e...
Hello, so as you can see, I am able to ping from one device to another as long as they are within the same room/have the same NWID. I am a beginner at setting these network diagrams up and I was sure I followed all of my teacher's instructions. Is t...
Hi Folks,Can't find much information on WIC-2T nowadays but we are looking for ways to make a WIC-2T module work on a Cisco 2901 ISR. I know HWIC-2T module is accepted but how about the old WIC-2T modules? Can it still be used on a Cisco 2901 ISR? An...
I have installed new NIC on my PC and configured attached ip and gateway. Also configured router with below configuration. I am able to ping from PC to router but not able to ping from router to PC. any thing i am missing?Router#sh run int fastEthern...
ARE THERE ANY COMMANDS WHICH WILL GIVE THE CHASSIS SERIAL NUMBER AS OUTPUT, FOR ROUTERS? ALSO, IF ANYONE KNOWS A COMMAND FOR SWITCHES THAT WOULD BE HELPFUL.
Dear Team,We used the following commands to check the throughput on our Cisco Asr 1001x router, and the outputs were as follows. However, their throughput different. When we use the show license command, throughput is shown as 10G, while when we use ...
Hi,I have a router c1104 with feature securitk9 (VPN crypto) and enabled license with on-prem license server..we tried to install the new version of IOS with classic mode, but when reload the router with the new IOS the router didn't keep the license...
Just trying to understand when the token refresh occurs for the QoS shaping mechanism. From my understanding tokens are put into the Bc token bucket (single-rate three colour bucket) at the Tc rate? Is this correct? Or are tokens put into the bucket ...
Hello friends,I am trying to understand the command "ip sla responder udp-echo ipaddress a.b.c.d port xx" but I have a doubt, the ip address (a.b.c.d) in the command refers to the local IP address on the device where it is being configured or it is t...
I wanted implement label distribution without LDP. To accomplish this I planned to use a dynamic routing protocol capable of distributing the labels (ISIS or eBGP). I set up a ISIS network and was able to configure mpls traffic-engineering tunnels an...
Hi everyoneI have a issue when a endpoints get ip address from Switch 9200 and router 1921 their Dns record A and PTR doesn´t update, they keep old record and IP.Someone have configuring "Dynamic DNS Updates by a DHCP Server" in cisco swtich/router? ...
Running CML 2.2.3 latest and it does not seem like you can connect with python cml and virl2-client anymore? Been a while since I have used this but just checking if i was using the wrong thing or something these days? ➜ ~ cml upException raised whil...
.jpg "VIP Master"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}