Dear All, Can anyone of you pls let me know the need for 3 Ethernet Ports in a Performance Route Processor on 12410 Router.Thanx in advance.Regards.
Dear All, Can anyone of you pls let me know the need for 3 Ethernet Ports in a Performance Route Processor on 12410 Router.Thanx in advance.Regards.
I can ping from PC behind two 2501s connected to a Linksys DSL router:Ip 192.168.l.1. However, the PC can not access the internet using the web browser. I have a Linksys DSL router as a perimeter router--access to the internet. The Pc and the two 2...
CYASIC Error Interrupt register 0x8 Parity Error internal to CYACYASIC Other Interrupt register 0x180 QE RX HIGH Priority Interrupt QE TX HIGH Priority InterruptCYBUS Error Cmd/Addr 0xD001A0AMPUIntfc/PacketBus Error register 0x0IOBUS Error I...
Hi,What is the connection speed for slots in a 7603,7606,7609,7613 when I use one sup720? Where can I find out the relation document in web pages of cisco? Thanks a lot.Sincerely
Hello,Lately, I started getting this error in our 6509 , running on Hybrid OS.The operation of the 6509 is ok until now. The error is as follows. Is it something serious ?.2004 Dec 19 07:11:47 %SYS-4-SUPERVISOR_ERR:Forwarding engine IP checksum erro...
What is terminal Server, How can i build it to access all my cisco router's console ports from one location.Can it be established with 2522 Router.
I need router with Four fastethernet port.Which series of cisco rouer will be appropriate for it.Please help me.
Dear allI have soho C828-Y6-M with ios 12.2(1)XE1I want to make traffic policing on ethernet interfaceto limit the traffic from one server to 128kis That possible , I tried CAR but it is not supported and also policy map I can't use it for policing c...
Hi alli know it is a native question.but can any one help me understand how the best effort worksif i have a link of 2Mbps , and customers are sharing this link having differnet speeds from 256K, 512K,1M,and 2Mhow will the traffic be distributed amon...
Hi, I have two routeres 3600 series and 4 of 1700's series, I want to config a static between 3600 series which has one serial port only to those 1700's routers series.any one who can help in this issue please .Thanks
Documentation states a 2501 router in bootstrap mode can load and execute system image from ROM or TFTP server. At the > prompt, the B command allows for TFTP server IP address and TFTP Server Name (is this the file name?) to load an IOS stored on TF...
Hello, All!Have a question: is it possible to make my Catalyst route one kind of packet (defined by ACL 172.16.0.0 0.0.255.255) and switch all other kind of packets via standart switching based on MAC.My objective is to migrate hosts from old address...
Is there some way to configure a management interface on a L3 device with other VLAN interfaces and NOT have it used as a routing interface?I am designing 4 6509's connected in a square using trunks. Some trunks will allow all VLANs (for HRSP). Oth...
Hi,Could you tell me how to enable the SSH on the Catalyst 2950.Thanks
Hi,I'll be upgrading the memory of our 3640 router. This is to accommodate on the new IOS ver12.3(8)T4 which has a minimum memory requirment of 16Mb flash and 96Mb DRAM.The existing flash memory of our 3640 is only 8Mb but have no idea on the DRAM. W...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-24-2025 06:42 AM | ||
| 02-26-2025 06:41 PM | ||
| 01-22-2025 07:00 AM | ||
| 01-22-2025 05:28 AM | ||
| 12-30-2024 06:12 PM |