Cisco has a tool called Pagent that runs on a cisco router and can generate traffic, bgp routes, etc. We are Cisco Gold partner. How can we get this software from Cisco? So we can test the QoS with Cisco equipment.
Cisco has a tool called Pagent that runs on a cisco router and can generate traffic, bgp routes, etc. We are Cisco Gold partner. How can we get this software from Cisco? So we can test the QoS with Cisco equipment.
Hi,I need to allow the administartor in overseas to dial in to my Cisco 1700 router to access the configuration through a modem phone line. So how can I configure the router for this task. Pls advice
Hello,I have problem to access a remote pix version 6.3.I can ping the pix but no access with telnet.Is there an other way to connect to the pix?
HelloI got the following parameters in my router :interface Ethernet0 description CRWS Generated text. Please do not delete this:192.168.0.10-255.255.255.0 ip address 192.168.0.1 255.255.255.0 secondary ip address 192.168.0.10 255.255.255.0 ip nat in...
I have an E1 link, where I would like to reserve say 20% of bandwidth for a particularly traffic type, but only if the bandwidth is needed; otherwise other traffic can use the full capacity of the link. Is this possible using "bandwidth" keyword unde...
Hi,i have two CISCO 3620 (IOS: c3620-is-mz.122-27.bin) connected over a switched LAN and both configured with a hsrp group.i always receive following message:%STANDBY-3-DUPADDR: Duplicate address 10.254.144.253 on FastEthernet0/0, sourced by 0000.0c0...
Hello,I have two site A and B. On each site I have a Cisco router C3600 with an E1/G703 (Serial0/0:0)interface + 1 fastethernet interface splitted on fast0.1 and fast0.2I would like to configure concurrent routing and bridging between the two sites b...
Dear all,this is about 3 switches 2950-48-EI having errors at the GBIC ports (WS-G5483) They are arranged in a triangle (MDF1, MDF2 and MDF3) using their Gigabit links. SpanningTree blocks one of the Gbic ports at MDF3.Now, MDF1 and MDF3 display Gbic...
Our client has a star topology network. The center is a 4503 depolying 48 port single mode fibre connecting to 4 remote locations. Each location has a 2955S-12 switch. The distances from remote locations to centre as below1st remote location to Contr...
Hello,I have two site A and B. On each site I have a Cisco router C3600 with an E1/G703 (Serial0/0:0)interface + 1 fastethernet interface splitted on fast0.1 and fast0.2I would like to configure concurrent routing and bridging between the two sites b...
Hi,I have several 2511 routers that connect to non-ciscorouters using dedicated async links. The links providetransmit/receive and ground only.The links work but if you ping the 2511 from the otherend of the link, 1 out of 4 pings fail (approx).Have ...
I have LMS ver. 2.1 include campus manager 3.2I would like to upgrade Campus Manager 3.3 Should I upgrade the LMS ?Or only upgrade to CM 3.3 ?where can I get this CM 3.3 upgrade file ?RegardsMohamed
Hi,When I configure the ACL with the time-range on Catalyst 4507-SUPIV running IOS Version 12.2(20)EWA, the the start time-range is not showing up.Here is what I did:Switch(config)#absolute start 14:30 04 Nov 2004 end 15:00 04 Nov 2004 Switch(config)...
Hi,we have cat6500 with sup720. We want to convert cat os to ios on them.Is there any procedure that define this convertion in cco?thanks in advance.
How do you make port security sticky on above switch running IOS 12.1(20)ew2. The sticky option is not available? Also how do you reset the port violation counter on a 3550.RegardsJohn Lipsett
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |